Search results for query: *

Get your hands on Australian Standard 1668.1 It gives a min m/s velocity across open doors and how many doors deemed open and depending on type of pressurisation system

Primary/Secondary chilled water system pumping The traditional primary/secondary pumping system is variable secondary pumps and fixed speed primary pumps with a decoupling line between Can you have variable speed primary pumps whereby the chilled water flow rate through the evaporator varies...

Hi LittleInch The new user is brand new, adding to existing users. Is the mass flow rate (kg/hr) the same either side of the PRV? R

Hello I have a boiler system in my factory running at 7 bar. I have a new user requiring 1,000Kg/hr of steam at 2 bar. I will have to install a pressure reducing station to drop from 7 bar to 2 bar. My question is will my boiler be delivering an extra 1,000kg/hr at 7 bar or will it be a...

Hello If I have a 10,000 kg/hr steam boiler but only run it at say 7 bar, is there a formula I can use to de-rate the boiler output to calculate its revised capacity in Kg/hr Regards R

Hello, Does anyone have a genuine control strategy to control and maintain minimum outside air on a VAV system? Thanks!

Drazen I understand the bit about taking in a small portion because that's all that is need to get to the desired RH, but why take in before the main cooling coil and deliver out after the main cooling coil. I have seen another installation on the same site and the dehumidifier takes in a...

I am upgrading an existing air handler and its BMS controls that is about 15-18 years old. The air handler looks pretty typical for Pharma with full fresh air, filters, heating coil, cooling coil and fan with zone reheats. Because the %RH requirements for the space are low, humidity 30%, they...

Dave, If I take any mod actuator 0-10v and break the 0-10 v signal will I use the 24 v power supply to operate on/off ?? Billy

Hi , I am looking for an actuator to work in a fire type situation for auto and manual control through a control panel The actuator is to be both modulating when in auto and on/off(open/closed)when in hand at the panel The actuator will be spring return and with power on it 24 V it will open...

Hello I have an air handling unit with a new steam to steam humidifier. The humidifier is fairly basis and maintains the room level humidity set point pretty good. Only thing is it sometimes sets off the smoke alarm in the supply duct and even in the rooms. Any tips for getting residual steam...

I have an air handlig unit that has a fixed outside air damper and a fixed return air damper. Outsdie temps vary from -5 to 25 dgeC so I want to add economy cycle control to the unit. I will install an entalphy sensor outside and one on the return air duct. If the return entalphy is greater...

Hi I am installing a heating coil directly in front of a centrifugal fan outlet in an air handler. I want to disperse the air before it hits the coil with a perforated plate infront of the fan. Does any one have informaiton or tech data on the idean distance between the fan and perforate plate...

I work in a facility with dozens of air handlers and fans. If one of the buildings goes into fire mode due to smoke detector alarm all the AHUs shut down as per the control strategy for that building. When the fire trip is cleared back at the main Fire Panel (usually after a fasle alarm) some of...

Hi I have a tablet press machine in the middle of a production room making tablets. Next to the machine (3 ft away) I have a desk with a weight scales on it for measuring etc...The desk is on 4 legs and bracketed to the back wall. There is a slight vibraiton coming from the floor when the...

Hi I have an old hot water storage unit with a name plast on it and it is as follows Maximum working pressure 0.8 bar Design Pressure 1.5 bar Test Pressure 3.0bar What is the difference between maximum working pressure and design pressure. I want to increase the current working pressure to...

Hi, Im looking at designing a new Dust Colleciton System, with an extract fan, turrit dust collecor unit and circular ductwork to 4 machine outlets points, approx 4" per outlet. I want to make it as efficient as possible. Not all machines will be operational at once. I would like to put the fan...

Hi, I am trying to design the local extract ventilation system in a lab. Over the lab benches the user want ventilaiton arms with a hood to stretch down over the bench to where chemical etc are been mixed & tested. What velociaty should I be looking for at the extract point? is there any code or...

SAK9 I like that idea of the mixing valve, it ensures my CHW retun temp is not any more than the design return so I will not upset the chillers. Any idea how i could get an estimation on cooling time if I sued say a 1 inch supply/reutn pipe?

Keep it simple... Ensure you seperate office areas from the likes of conference rooms or higher occupancy area so areas of equel proportions of outsdie air are on the same HVAC system. e.g. offices may require 10% outside air, conference rooms require 25% outsdie air, best have have these of...