Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: gramya
  • Order by date
  1. gramya

    Atmospheric Ammonia Storage Tank

    I know of an expert who has handled 10 such storage planning commissioning deccommissioning in India. He may be of some help. you may try to contact for some useful tips. I am also trying to contact him, but he is in Doha Qatar for training programs on a relevant topic, Hazardous Chemical...
  2. gramya

    NaOH Pipe Sizing

    There shall be no problem even if you increase the pipe flow velocity to around 5 ft/sec. Rather, it helps to avoid any solids deposition. If the pipe length is small you may increase to 7ft/sec if you had faced the solids deposition as your operating problem. Do not oversize the pipe for such...
  3. gramya

    Corrosion rate of steel in saltwater

    I had worked in a process plant which used sea water extensively as cooling water and then the process plant was salt based plant producing Soda Ash ( Sodium Bicarbonate). We had measured the corrosion rates on Cast Iron and Steels. The sea water had around +28000 ppm chlorides. The atmospheric...
  4. gramya

    Help Finding Pipe Flow Software

    Try to use the PlantFLOW software by Bentley. You may visit www.bentley.com and see the list of software under plant engineering analysis. I have used this software extensively for similar work and for analysing fire water system of big process plant. My interest was also sizing the suitable...
  5. gramya

    Plant Design Software

    If you mean the software used for modelling of plant P&I Diagram generation, layout, piping layout, etc then there are many competing ones like AutoPLANT, PDS, PDMS, EPLANT, etc. You may visit few of their websites for more details www.bentley.com, www.e-eplant.com, Hope it helps. Narendra K...
  6. gramya

    AS 1210 - FEA x Analytical calculation

    I agree that the FEA is the choice when you do not have a proven design and stress analysis theoretical methods. FEA assumes lot of conditions and then arrives to the best stress distribution in the area of concern. However, it is prudent that we cross check such FEA with experimental stress...
  7. gramya

    Material selection for ph 2 to ph 12

    I had worked in a Soda Ash plant and the liquids we handled were of similar characteristics as mentioned by you. Peoplew in the plan were using cast iron plug, ball and butterfly valves but with lot of maintenance problems. We started experimenting with Butterfly valve, nitrile rubber lined...
  8. gramya

    Piping Design Software Selection

    Have you heard of EPLANT- Piping, P&ID and STH for 3D plant design. this product is developed by RELSOFT Argentina? You may visit their site www.e-eplant.com for more details. The product is copmatible with AutoCAD 2000 and other recent issues. I am told that it costs reasonable. Give a try and...
  9. gramya

    Sea Water Service Pipeline, 316L?

    Interesting. The replies of the experts indicate that for sea water carbon steel or lined carbon steel, stainless steel, FRP, PP, superaustenitic stainless steels, cupronickels etc are all used at one or the other place. Who says that SS 316 or 316L is not used in sea water service. All RO...
  10. gramya

    Nozzles-Bending Moment in Sect.VIII-1 App. 1-7(b)

    All the current and good software on PV design have the calculations done for you. You may try COMPRESS for the purpose and gives you all the calculation process in the reports so generated for the design of large openings in the vessels as per the ASME Sec VIII Code App. 1-7 Narendra K. Roy...
  11. gramya

    Maximum Value Of Bending in Columns

    The good engineering practice for petrochemical and chemical plants indicate that the deflection of the tall verticla vessel shall remain within 5 mm per meter which works out 6 inches for 100 ft. All good consultants for project engineering follow this criteria and it appears in their tech...
  12. gramya

    overview of ASME pressure vessel design code

    There are efforts specifically for the same purposes to refresh or help engineers to appreciate the salient points of pressure vessel design as per ASME Code Sec VIII Div 1. Some good correspond course through email issues are now available. you may visit the www.charismaglobal.com and view the...
  13. gramya

    Emailing Project schedule (Gannt) to others w/o MS Project.

    Your boss can keep an evaluation mode MS Project valid for 60 days and use it for his viewing and if the activity is to prolong for more than that, he may purchase a license, which will not cost more than 600 US $. Narendra K. Roy Gramya Research Analysis Institute, PO box 4016, Vadodara...
  14. gramya

    What are the best piping materials

    The best and most acceptable material shall be carbon steel, and the pipe to specification ASTM A106 Grade A or B. I presuem that schedule 40 will be safe to be used. Narendra K. Roy Gramya Research Analysis Institute, PO box 4016, Vadodara 390015, India Website: www.gramya.com ...
  15. gramya

    Piping size versus total output

    I hope that the flow quantity is more related to the allowed velocity in the pipe. A water velocity of upto 10ft/sec in noncritical application shall give you the flow. Generally discharge lines to pumps are designed with 6-8 ft per sec velocity for long distance transfer of water. Your inlet...
  16. gramya

    More than 2 saddle supports, Zick?

    Interesting problem. It has been raised number of times and the same answer that shell become an indterminate structure once supported on more than 2 saddles. But cant we analyse the cylindrical structure supported on multiple supports? The calculation for stresses at mid section of the shell...
  17. gramya

    UT instead of X-Ray

    RT had been used since long as acceptable NDT for fabricated pressure vessels. UT was always used as complimentary technique to furthe investigate the defect sizes. The recent developments have brought UT at the forefront as the most reliable technique for defect evaluation. If you are aware...
  18. gramya

    6" Dummy Leg Support on 12 " pipe

    Coming back to more authentic and detailed analysis, which is not easily possible manually, one may try WinNozl ( again Paulin software, marketted by Bentley, earlier Rebis). I have myself demonstrated the use in such trunion support cases and even for vertivcal vessel supported by pipe legs...
  19. gramya

    Stress analysis of cross country piping

    There is another very useful software which takes care of the buried pipeline. It is AutoPIPE Plus now licensed by Bentley ( earlier with rebis USA). The analysis takes care of the earth pressure, frictional longitudinal stresses imposed on the buries pipeline as it tries to expand due to...
  20. gramya

    Australian Standards

    May I get the contact website for procuring Australian Pressure Vessel and heat exchanger, Tank and process piping and pipeline standards. A similar help is needed for New Zealand Pressure Vessel and Piping standards Narendra K. Roy Gramya Research Analysis Institute, PO box 4016, Vadodara...

Part and Inventory Search