You need to talk with a hydraulic seal vendor, give them approximate dimensions and they can find a seal for you. These are very common seals and the only thing they may need is the fluid type and temperature so they can select the correct seal composition.
Dennis
SolidWorks 2013
Dell...
Have a need for a right angle drive. Input hollow spline shaft through, male shaft output. Consider a X-Y axis slide arrangement where the Y axis is driven by a ball screw and the X axis is driven by a spline shaft. This allows the X slide to move at any position on the Y axis. May sound a...
You might look into someone in your area that does flame spray. The company I work for does a lot of machine repair and we flame spray weld to build up worn surfaces. If done correctly you wouldn't even know it's been done.
Hope this helps.
SolidWorks 2013
Dell Precision T3500
Nvidia Quadro...
SincoTC,
You hit it right on the head. I started using a new Microsoft wireless keyboard and mouse. Love it but it does have a short coming, no indicator lights so you have to hit a key to check it's status. Sure enough it was the damn NUM LOCK key. Thanks guys for the quick response.
Dennis...
I started to use SolidWorks this morning, started a sketch and I'm not able to modify the dimension. Sketch circle, size shows up highlighted, try to change and it will not take the new dimension. This was working fine last night, I have rebooted the computer several times and it has no effect...
Answered my own question. Drew a small circle on one corner of the layout and patterned the circle on the x and y axis.
SolidWorks 2013
Dell Precision T3500
Nvidia Quadro 2000
Dual Monitors
Hello All,
I am doing a plant layout and was asked if I could plot it with a grid. Of course I said yes knowing I could display a grid. Well it seems that grid won't plot. Any ideas short of drawing grid lines?
Thanks in advance.
SolidWorks 2011 SP4
AMD AthlonII X4 620
Windows XP X32 Pro...
Maybe a little late but have you considered using a shrink disc? Look at B-Loc split ring.
SolidWorks 2010 SP4
AMD AthlonII X4 620
Windows XP X32 Pro 2.5GB RAM,
Nvidia Quadro FX570,Dual 19" widescreen
Logitech Wave wireless keyboard and mouse, Space Navigator
Try to find some older Drafting textbooks, they were full of castings and other exercises. That's what I did when I started using SolidWorks 2001 plus...
SolidWorks 2010 SP4
AMD AthlonII X4 620
Windows XP X32 Pro 2.5GB RAM,
Nvidia Quadro FX570, 19" widescreen
Logitech Marble Mouse, Space Navigator
Gupta65,
Thanks for the info.... don't kill the messenger, thank you.
SolidWorks 2010 SP4
AMD AthlonII X4 620
Windows XP X32 Pro 2.5GB RAM,
Nvidia Quadro FX570, 19" widescreen
Logitech Marble Mouse, Space Navigator
Jack,
I don't have the answer, just wanted to say nice scopes, I have several.
SolidWorks 2010 SP4
AMD AthlonII X4 620
Windows XP X32 Pro 2.5GB RAM,
Nvidia Quadro FX570, 19" widescreen
Logitech Marble Mouse, Space Navigator
I have been using for almost two months working fine. No problems and I haven't done anything about downloading drivers other than what it came with.... Gotten a lot of interest from others at the new job....
Merry Christmas Everyone...
Dennis
SolidWorks 2009 SP0
Dell Precision T7400 Xeon...
Well guys new job and computer. Closer to home and compare signature from the one above. I am in SW Heaven.
Dennis
P.S. was a bent pin on connector and it now works as expected. Thanks.
SolidWorks 2009 SP0
Dell Precision T7400 Xeon 2.5GHz
Windows XP X64 Pro 8GB RAM,
Nvidia Quadro FX4600
Dell...
MadMango: Will try that when I get a minute. You're right about the monitor but it is a 17". [pipe]
CBL: I didn't do that but tried it last night and the same result. [pipe]
Jeff: It never fails, just do enough to get by and you are continually upgrading.
I may also try a slightly newer...
Hello,
I have upgraded my home computer to use a Nvidia Quadro Fx500 AGP. I know very sad... anyway it works but I have basically lost my color red. No adjusting will bring it back. Is it a bad card or my 10 year old monitor? I know not much to go on I just need a place to start. I had a 3d...
Thanks everyone, I'm at home so will try when I get into work in the morning. I think I'm most comfortable with the revolved cut but just for kicks will try the loft. I've never been able to get the image thing to work for me, sometime I'll try again.
Thanks again, I love this forum.
Dennis...
Hello All,
I will try to describe my problem and if it's a simple fix excuse me for asking. I have a yoke shaped part and I only want to chamfer the radius and not the flat leading up to the radius. I have turned off "tangent propagation" and cannot just chamfer the radius it automatically...
rikonen,
Not having any problems with our 650C but I'm on SW2008 SP2. Only print "D" size on this plotter. I believe when we installed it a year ago I used the latest driver available. And no I don't think they are updating drivers for new apps. I would be interested if problems are developing...
