Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JAE on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Metalero

    J integral determination from DIC

    Hi. Look first at ASTM E1820-20b
  2. Metalero

    What is the difference between PSL 1 and PSL2?

    The PSL2 pipe is manufactured with more limited controls, both in the raw material, process and the pipe itself. It is intended to reduce the probability of premature degradation, resist the fracture propagation, HIC and the others well known damage mechanisms that could lead to fatal failures...
  3. Metalero

    Pipeline isolating device: Is there anything newer or better?

    Thanks Littleinch. I'm not looking for an specific improvement. But it has been the same for a long time. I was reviewing the standards: NACE RP 0286 becomes SP0286 in 2007 and it has been all about it. As you say: If it isn't broken why fix it?
  4. Metalero

    Pipeline isolating device: Is there anything newer or better?

    Hi everybody I'm looking for the art's state about Pipeline isolating devices. I see the typical and well known Monoblock joints and/or flanged joints, but someone knows about some improvement in this technical or any better or newer device to isolating catodically protected pipelines? Thanks...
  5. Metalero

    Fracture Surface Failure mode identification

    Share your results (if possible).
  6. Metalero

    Effect of specimen geometry on impact strength

    if you are using CVN test, the lenght also is important, since duration of test could be shorter if the test piece is shorter too, hence the energy could be lower than real. At the opposite side, if the test specimen is larger, more friction over the anvil, more energy to fracture
  7. Metalero

    Fracture Surface Failure mode identification

    To my mind: The shiny silver region that you mentioned is a mechanical damage post fracture, however welds are fatigue susceptible too and don't have fatigue limit (10^6) as the base metal, and more discontinuities are possible.
  8. Metalero

    Fracture Surface Failure mode identification

    It is correct, it corresponds to ratchet marks (fatigue), which can be generated even by the roughness of the surface, without the presence of a "significant" defect. I can´t detect the weld in your photos. In the first photo there is an area between 11:30HT and 2:30HT that looks different...
  9. Metalero

    Fracture Surface Failure mode identification

    Answer 1: Yes. The pattern of circumferential lines along the fracture surface is a pattern of beach marks that extends outward. River lines indicate propagation from the internal diameter. The beach marks seen in the detailed pictures may correspond to secondary starting points. Answer 2. Yes...
  10. Metalero

    I am looking for the material speci

    Context: appear like that in Old pipeline and petrochemical plant's draws. No more info.
  11. Metalero

    I am looking for the material speci

    I am looking for the material specification: STD SLA 904, have you heard about it, could you guide me?
  12. Metalero

    hi guys. My question is " how to d

    1. May be this post help you: https://www.eng-tips.com/viewthread.cfm?qid=341586 2. May be "Pipelines Rules of Thumb" be usefull...
  13. Metalero

    Aqueous ammonia storage tank

    The text says: Ammonia gas dissolves well in water giving rise to alkaline solution. Ammonia gas and its solutions are corrosion inhibitors of carbon steels. In some cases, the humidity are used to inhibite the anhydrous ammonia (1 - 2%), ex. during its rasnportation.
  14. Metalero

    Low Carbon in MS 1047-1

    Did you take into account the oven efficiency value in the load calculation? If so, maybe you overestimated it.
  15. Metalero

    Link between suction and volume

    Did you verify that the filters are the same, type, material and mesh or number? The capacity and efficiency of the pumps is also a crucial factor, is the same or proportional?
  16. Metalero

    SPE Professional Engg Exam Preparation

    just Google it Maybe this be usefull for you
  17. Metalero

    ASME WPS and PQR documents

    Here some options [DOC] WPS [DOC] PQR
  18. Metalero

    corrosion rate in HF and HCl

    Not exactly as you ask but maybe be more than 50 mil/yr, since each acid without mix have this value (and just i have for class of steel, not for specific one.
  19. Metalero

    Material selection & industry standards

    Check the Matweb’s page http://www.matweb.com When you search for a material, multiples options appears and there is descriptions and a list for standards and denominations related to the same material, and of course, there is properties and technical information about.
  20. Metalero

    Material selection & industry standards

    Ashby's Method book: https://books.google.com.mx/books?id=K4h4CgAAQBAJ&lpg=PP1&pg=PP1#v=onepage&q&f=false wiki: https://en.wikipedia.org/wiki/Material_selection

Part and Inventory Search

Back
Top