Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. TheLaserburns

    Laser rust remover safety question

    Beings though the link you provided is now not available may answer some questions If you ask me to do something, I will do it. There's no need to nag me every 6 months
  2. TheLaserburns

    cuting parameter

    I don't know the laser but your nesting software should have a vaporization setting such as engraving to burn the film away first then do a cutting pass. Or just do as I do and peel it off before I load it onto the machine. But then again the finish on the SS isn't critical for what I...
  3. TheLaserburns

    MMC user name nad password

    Try Username by Password ch3362 If you ask me to do something, I will do it. There's no need to nag me every 6 months
  4. TheLaserburns

    Bystronic Bystar 3015 shutter error

    Hello Steve, My error code book says the following for the E7 error.... The lifting cylinder has been moved by hand. Check for manual operation. Controller error. Then the usual Contact Bystronic Customer service. Didn't know it was possible to take manual control over the shutter but I will...
  5. TheLaserburns

    Amada 3015 problems with 1/4" stainless

    It's not how the part has been drawn ??? I had a customer supply a dxf drawing with an issue like that. All vertical cuts were not there . I had to redo the cutting technology on it with my own software. Just a thought. If you ask me to do something, I will do it. There's no need to nag me...
  6. TheLaserburns

    Bystronic Bystar 3015 filling with gas problem

    Steven, You can also go into Laser view and reset the error. it may give you 5 to 6 more different errors but can sometimes start the filling with gas step. I've had these same issues before. First time it was fixed by doing what I said above. The next time I had a leak in the glassware so bad...
  7. TheLaserburns

    Bystronic Bystar 3015 filling with gas problem

    First and easiest place to check for a leak is the yellow hoses inside the laser cabinet ( see pics) providing they are still the same ones fitted factory. Vacuum lines are always yellow. You don't need to touch the yellow one's that are in the gas mix rig though. You need to undo fittings and...
  8. TheLaserburns

    Amada 2415 Tape shot not working

    I don't know the Amada but I'm sure the same principle can apply. With the Bystar if the alignment is way out I have to take the nozzle off put the tape on again and do a shot that way. Could be firing way way off to one side so needs a heap of adjustment. When you have it back near the center...
  9. TheLaserburns

    Bystronic 3015 btl 2800 with cnc 90

    If that is an actual battery and you can't find a button battery on the PC's mother board then it probably is the one. I just have never seen battery like that in a computer before. May be an old comp. If you ask me to do something, I will do it. There's no need to nag me every 6 months
  10. TheLaserburns

    Bystronic 3015 btl 2800 with cnc 90

    Jonathan, No the white and green thing is a capacitor. The battery you are looking for is a button battery like the one you would see inside a watch only bigger. About the size of your thumb nail. If you ask me to do something, I will do it. There's no need to nag me every 6 months
  11. TheLaserburns

    Bystronic 3015 btl 2800 with cnc 90

    You need to replace the small button battery inside your computer that will get rid of one problem. As for the not finding your cutting plans you may need to tell it where to look for them again it's forgotten the pathway. If you ask me to do something, I will do it. There's no need to nag me...
  12. TheLaserburns

    Bystronic Drives not ready error

    You normally get that error after a head collision. Try doing a CNC Reset/restart from in the administrator menu.See if that helps. If you ask me to do something, I will do it. There's no need to nag me every 6 months
  13. TheLaserburns

    Bystronic Bysprin 3015 excitation problem

    We had the same issue here. Just replaced the fan and good as new. This is one of the many errors you get in regards to leaks. If you ask me to do something, I will do it. There's no need to nag me every 6 months
  14. TheLaserburns

    machine layout

    No bottle neck using this method. You can normally unload the cut parts before the cutting of the next sheet is finished. Depending on how many parts are on it of coarse. We store our most common cut steel right next to the loading bed ( you can see it just on right of the pic )and other steels...
  15. TheLaserburns

    machine layout

    We have a Vacuum lift to load our sheets. Will lift up to 300kg If you ask me to do something, I will do it. There's no need to nag me every 6 months
  16. TheLaserburns

    Strange tape shot

    For comparison mine is set to ( Bystar 3015 5Kw ) Pulse width, single pulse 20 Laser power, single pulse 20 That gives a 1/2 mm hole in the tape. Good to see your back on track If you ask me to do something, I will do it. There's no need to nag me every 6 months
  17. TheLaserburns

    Strange tape shot

    Try unscrewing the nozzle and sticking the tape to the nozzle body. Do another shot like that and see where it is. Your alignment may be way out off to one side. Adjust it to center then replace nozzle and fine tune it from there. If you ask me to do something, I will do it. There's no need to...
  18. TheLaserburns

    becker blower bearings

    Not sure if this helps. Its listed on the back of our operating manual for our Becker Blower. Website https://beckerpumps.com/ Email beckerpc@bright.net If you ask me to do something, I will do it. There's no need to nag me every 6 months
  19. TheLaserburns

    Plumbing for Cutting/Resonator Gases

    ON our Bystronic Bystar 3015 5.2kw we have copper all the way for the laser gases ( N2, He, Co2 ) and braided hose from the bottles to the Regs then copper the rest of the way for the cutting gases ( N2 and o2 ) That's how it was set up in Germany so that's how they set it up here in Perth when...
  20. TheLaserburns

    Amada 2415nt cutting condition problems

    When you say small noticeable dross do you mean molten metal or small beads that you can rub off with you hand or a file rather than a grinder ??? If it's the first then it's more likely a gas pressure issue not enough to blow the molten material away fast enough, if it's the second then it's a...

Part and Inventory Search

Back
Top