Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JAE on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: sanvik
  • Order by date
  1. sanvik

    Replacing through-hole type components with SMD components

    It's possible that this design was created with a big reserve in mind, so using heat-sinks & fuse might be overkill for the purpose. I saw similar device (SMD PCB), where output connected to IRF8313 Power Mosfet without heat-sinks. It max total current is 5A though.
  2. sanvik

    Replacing through-hole type components with SMD components

    So I should use MOSFET with lower Thermal resistance junction-case RthJC value, smaller the value it is better the heat radiation. Would be these a good substitute: Infineon [link...
  3. sanvik

    Replacing through-hole type components with SMD components

    Should I consider another Mosfet with more power dissipation? Which model would be suitable?
  4. sanvik

    Replacing through-hole type components with SMD components

    Theoretically, max power is 2A x 12V = 24W per driver circuit: so I still have some power reserve? Possibly, I can use copper area around DPAK Mosfet for heat dissipation?
  5. sanvik

    Replacing through-hole type components with SMD components

    Can be 27N3LH5 Power Mosfet TO-220 replaced with DPAK version without heat sinks?
  6. sanvik

    LM348 substitute

    Two LM348 op-amps in this circuit. So is it OK?
  7. sanvik

    LM348 substitute

    If we replace LM348 Op-Amp with TL074 Op-Amp, this is a direct substitute, and no changes are needed in passive components in circuit?
  8. sanvik

    Switch input mode with jumper

    Mainly, just low profile and reliable, low PCB space.
  9. sanvik

    Replacing through-hole type components with SMD components

    For THT cdesign, would be fine to use resistors with 1/4W power rating for all elements or it need be calculated? If use SMD design, what is common SMD resistor size (Code) that can be used here? (Imperial/ Mectric)
  10. sanvik

    Switch input mode with jumper

    well, I mean internal switch on PCB (J4)
  11. sanvik

    Switch input mode with jumper

    Yes, internal jumper, or DIP switch. DIP switch perhaps better, I need SPDT DIP Switch (ON-ON, without center position). Searched on Digikey, but still didn't find good accurate one. The line-in input is Terminal block, not 1/8" plug socket, and Mic is on board.
  12. sanvik

    Switch input mode with jumper

    Could anyone suggest switch/input selector for mounting on PCB (through-hole)? Device have two inputs, Mic and Lin-in input. Capsule Micro Electret Mic Ø10mm in mounted on PCB, Mic is default input mode. When I need switch to Line-in input, I just put jumper. Or maybe some other small handy switch.
  13. sanvik

    Replacing through-hole type components with SMD components

    For through-hole mounting trimpots, Digikey offer 120 models for given criteria. What type is better suitable for application? does Tolerance % matter?
  14. sanvik

    Replacing through-hole type components with SMD components

    Normal means "for indoor use". -10C to +60C / 14F to 140F Not in aerospace industry. :) @BrianG For myself, yes. You are absolutely right, assembling SMD PCB professionally at home is very difficult, and also requires a very sharp vision, and solid hand-soldering skills. I didn't plan to...
  15. sanvik

    Replacing through-hole type components with SMD components

    Normal conditions, no anything special.
  16. sanvik

    Replacing through-hole type components with SMD components

    Is there anything else wrong in mixed technology, when use SMD + some Thru-hole components in one PCB, except more complexity and thus extra cost? In terms of reliability?
  17. sanvik

    Replacing through-hole type components with SMD components

    @itsmoked Thanks for the helpful advices! Will try to follow it. Those TO-92 transistors - 1 x FET J310 and 5 x 2N3904 is only available in TO-92 package. Power MOSFET 27N3LH5 have DPAK SMD package, but with less Total power dissipation 30W, these Power MOSFETs drives the current (1W LED...
  18. sanvik

    Replacing through-hole type components with SMD components

    Which resistors do you mean? Its Terminal Blocks, there is pin spacing (pitch).
  19. sanvik

    Replacing through-hole type components with SMD components

    Its for myself, not for mass production, though. SMD PCB is much smaller and looks better. I can stay with through-hole design though, just need make new PCB a little smaller. Design it not mine. Which terminal block model is usually used in such design for wire-to-board wiring? (commom Pitch, mm).
  20. sanvik

    Replacing through-hole type components with SMD components

    Yes, I looked for some SMD versions of that components. In particular, I am not sure about SMD trimmer potentiometers: although they are not intended to use it very often, they are extremelly small size 5x5mm, and seems it will be very difficult to tune/adjust it with screwdriver. What's power...

Part and Inventory Search

Back
Top