Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JAE on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. MtnJunkie360

    2d verify

    In this install of NX, 10.03 mp6. I'm getting Replay, and 3D, but no 2D verify, is this normal?
  2. MtnJunkie360

    Features you wish NX had?

    I added the convert file into the windows context menu. right click -> convert to inch right click -> convert to MM Seems to work fine. but yes, its not on the fly inside NX.
  3. MtnJunkie360

    Features you wish NX had?

    The ability to use a "Datum coordinate system" or preferably a MCS as the reference Coordinates of all point dialogue box's and line creation/edit dialog box's. This comes into play for me in many places, manual edit of toolpath, creating points, creating 3D lines to drive tools down. Most all...
  4. MtnJunkie360

    HoleMaking IPW shown in assembly.

    Say i modeled a piece of tooling, pulled that fixture into my manufacturing setup as an assembly component for visualization. And also, inside the fixtures .prt file, i made some programs to machine the fixture using holemaking. Now, inside my manufacturing setup for my actual part, all the...
  5. MtnJunkie360

    On Machine Probing in NX question

    Using NX 10.0.2.6 and a Makino A51NX Hroizontal with renishaw Probe. Using NX OOTB Probing functions, and the OOTB Probe ugti0402_001 Ive gotten it to position B axis using "Rotary point vector move" subop Then i protected mode rapid to near the point using "linear move to point" subop Then...
  6. MtnJunkie360

    4th axis Post and tool axis with A and B tilt.

    Hello Ive discovered an issue with my post that ive used for years, that I'd like to come up with a fix for. Its a 4th axis Post for A axis. I just ran into an issue that if i accidentally have a slight B tilt to my tool axis in an operation, that i dont get the correct A number in the code...
  7. MtnJunkie360

    "Extrude" a solid body, along a series of curves.

    I'd like to Drive a solid body along a series of curves. Kind of like the "Tube" feature, but the body isn't round, nor perpendicular to the curves. It has depth beyond the end of the curve.
  8. MtnJunkie360

    Mill a slot, with a ball bottom, where its not deep enough to reach ballmills tangent.

    I've modeled a vacuum fixture, and it has a grid pattern of ball troughs. Trying to get a ballmill to run down the center of them all. The troughs are only .03 deep so not up to tangent of 3/16 ballmill, to mill it as a real slot.
  9. MtnJunkie360

    NX CAM 9.0 New Feature question.

    IPW Flow? If I'm just programming a single part, like in vises. I program the top side, then new MCS spun around "and usually moved to tooling surfaces for ease of setup" , to Program the bottom, That works fine, for the IPW being cut properly from one op to another. Is that what you mean by...
  10. MtnJunkie360

    NX CAM 9.0 New Feature question.

    In NX 9.0 there's the new multi part programming feature. On one side of a Horizontal Tombstone I have multiple of the same parts. Program one part, Paste to the other parts with associativity to first... All is well. But is there a way for on another face of the tombstone, to have the second...
  11. MtnJunkie360

    NX 9.01 Shop Doc Template Modification Problem.

    That actually worked, thank you. First I set them all to general, then for aesthetics slowly put some back to numbers to not get 15 zero's after the decimal. In the end its fixed, and all the ones that matter are back to numbers with few decimals. Not sure which one was the culprit.
  12. MtnJunkie360

    NX 9.01 Shop Doc Template Modification Problem.

    Thank you for the reply, but yes definitely doing the Sheet only as the guide stated. "though since I was unsuccessful, have tried all different ways to no avail."
  13. MtnJunkie360

    NX 9.01 Shop Doc Template Modification Problem.

    I've been trying to follow a guide to make small changes to the shop docs. Link At the part where in Excel, you Publish the .Xlsx into a new .htm is the problem. Even without altering the .xlsx just open in Excel, and republish the .htm makes NX throw a bunch of .tcl errors trying to use the...
  14. MtnJunkie360

    Tool Description Variable

    Solved, sorry.
  15. MtnJunkie360

    Tool Description Variable

    In NX 8.5, when using a tool from the library, there is the catalog name... But if you click in to edit the tool, there is also a tool description ie... tool UGTI0201_012 has a description of " End Mill 1/2" " is there a mom variable to pull this description into post builder?

Part and Inventory Search

Back
Top