Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: ijzer
  • Content: Threads
  • Order by date
  1. ijzer

    ASME VIII-1 Code case2626

    Code case 2626 (in short) states that the calculation of the required by thickness UG-16(b)(5(d) (which referes to UG-27 calculation method) may be waived provided that : the minimum thickness shall not be less than calculated per UG-27? Looks like i am in a loop here. Can anyone clarify?
  2. ijzer

    PWHT time ASME 1 versus B31.1

    According ASME 1 the minimum PWHT time for materials P15E (like SA-335 P91) with thickness over 5 inch is 5 hours. For ASME B31.1 the minimum 5 hours is required already over 2 inch thickness. Does anybody know why this difference or could this be a typo in B31.1?
  3. ijzer

    SA 350 LF2 in a ASME 1 system

    Material SA 350 LF2 is not accepted for pressure parts in ASME 1. Is it allowed to use this material in a B16.34 valve in an ASME 1 system?
  4. ijzer

    "S" stamp valve

    A valve according B16.34 is located in a B31.1 BEP, the valve contains a weld ,does it need to be supplied with a S stamp? Same question for a Desuperheater containing a weld, does it need to supplied with a S stamp?
  5. ijzer

    AWS D1.8 UT technician qualification

    AWS D1.8 par 7.2.4 (2) only allows ASNTC-1A level III technicians to perform UT where as par. 7.2.4.(1) allows level II and III technicians if qualified by employer. Qualification by employer shall be at least by ASNTC -1A according par. 7.2.2. I'am lost here. Can somebody explain the...
  6. ijzer

    Steam /air decoke EDC coils

    In EDC furnaces, coils made of Incoloy 800H ,what is the maximum steam/air decoke temperature used currently.
  7. ijzer

    Copper alloy NRB

    Does anybody know what type of copper alloy is NRB. What would be the C number or chemical composition?
  8. ijzer

    Radiant coil cracking Heaters

    A complete cracking Heater (radiant and convection sections)is supplied with C-E marking accoerding PED. Is the replacement of the radiant coil considdered as a repair (not subject to PED) or is it a new equipment and shall it fulfill PED.
  9. ijzer

    Corrosion rate for 316L in Demi water

    Does any body know the corrosion rate of 316L in deminaralized water in the temperature range 40 to 80 Deg. C
  10. ijzer

    Key fitting tools

    Does any body know where to buy special tool for opening key fittings e.g. horse shoe type.
  11. ijzer

    SS Type 347THS

    Does anybody know what "THS" stands for in material type 347THS
  12. ijzer

    Impact test KCU/KCV

    What is the conversion from Charpy U values to Charpy V values or vise versa ?
  13. ijzer

    Corrosion Monitoring naphtha

    Has anybody experience with on line corrosion monitoring in a naphtha heater. (mainly sulfiric corrosion). what type of monitoring is used?
  14. ijzer

    Youngs modulus Ultra High strength Steel

    Can any body provide me the E-modulus of Weldox 700 steel. This is structural steel with a yield of 700 MPa and a tensile of 800 MPa. Required are E at 20 Deg. C and at 200 Deg. C
  15. ijzer

    Nb content scattering in 347H material

    What could be the explanation of having a difference in Nb content of more than 1% in a 347H tube (stabilised annealed),between the outsidesurface and the inside surface.

Part and Inventory Search