Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. MachineryWatch

    Accelerometer Adhesives for Permanent Installation

    Does anyone on this forum know of any accelerometer manufacturers that have tested Belzona 1111 for installation of mounting pucks used for installation of accelerometers. Or, perhaps any other source for this kind of information. I want to make sure the high frequency performance of the sensor...
  2. MachineryWatch

    ARTeMIS Modal Software

    Anybody care to comment on their experience using the ARTeMIS Operational Modal Analysis system? I'm considering it. Performance? Support? Any feedback would be helpful. Thanks in advance. http://www.machinerywatch.com
  3. MachineryWatch

    Microphone Selection, Vehicle Testing

    I will be doing some sound and vibration work on horse trailers soon to compare and contrast the effects of different construction methods. Can any of you NVH guys recommend an appropriate microphone for such an application? I appreciate your help. http://www.machinerywatch.com
  4. MachineryWatch

    PC Startup or Wakeup

    Is there a way to get a laptop or tablet PC to startup at predetermined times of the day, run a program and then shutdown again? Skip Hartman http://www.machinerywatch.com
  5. MachineryWatch

    FM Signal Demodulation

    Hi, I have recorded an encoder signal from a rotating machine. It is captured as a .WAV file. Is there a signal processing software available to "demodulate" the signal? I am interested in the torsional vibration of this machine's shaft. The encoder signal should contain this information as...
  6. MachineryWatch

    Signal Processing Artifacts

    I have been collecting vibration data on a paper machine press section that has abnormally high amplitudes at around 28 Hz. It is believed to be a resonant condition. The vibration sensors are accelerometers. The sample rate is 320 samples/second. This yields a 0-125 Hz FFT. When I record...
  7. MachineryWatch

    Hilbert Transform In Spreadsheets

    Has anyone here set up a Hilbert Transform routine in a spreadsheet? If so, was it difficult to program? Skip Hartman http://www.machinerywatch.com
  8. MachineryWatch

    FFT Interpretation

    I positioned a photocell speed sensor, that generates a TTL signal, to read the passing vanes of a cooling fan on an engine driven generator. The speed was 3600 RPM (60 Hz). There were 14 vanes on the fan. I ran the signal to an FFT analyzer. The FFT is 0-1000 Hz with 3200 FFT lines. The...
  9. MachineryWatch

    Wound Rotor Motors

    What unique features should I look for when diagnosing problems with wound rotor motors? Skip Hartman http://www.machinerywatch.com
  10. MachineryWatch

    Hydro-Turbine Cavitation Detection

    I am working on adding capability to an existing hydro-turbine monitoring system. Primarily it is using vibration sensors, both accelerometers and eddy current (proximity) probes. The owner wants to add cavitation detection. I am familiar with the audible sounds pumps make when they cavitate...
  11. MachineryWatch

    Engine Driven Generator Vibration Amplitudes

    I have been testing a V6 (4.2L) natural gas fuel, spark ignition, emergency generator running at 3600 RPM. The 1X RPM vibration amplitudes at all load conditions approach 1 inch per second on the generator bearing (spectrum peak). There is only 1 generator bearing on the outboard end of the...
  12. MachineryWatch

    Torsional Stress Fractures

    Long distance runners are plagued with stress fractures in the bones of their feet due to the constant, repetitive "impact tests" their feet are subjected to with each step. Each step produces an impact which excites the natural frequencies of the bones. The constant excitation of...
  13. MachineryWatch

    Velocity & Displacement

    I am working on a project to monitor the structural vibration of a hydro electric dam. Sensors are located on the dam and the penstocks which carry water to the turbines. The purpose is to identify changes in the structural response of the dam rather than condition monitoring of the machinery...

Part and Inventory Search