Hi there
I have three channels modeled using swept feature. I want to connect them with a nice looking blend.
Normal Edge Blend doesn`t satisfy me but it works fine when I want to offset the blend surface
Styling Blend from the other hand satisfies me but it doesn`t work when I want to...
Hi there
What would be the best way to wrap a curve ( spiral ) on a surface ?
I attach the prt file as well as a paint sketch.
I have been trying to use a wrap curve but it doesn`t work on a multiple face sheet. Also the surface size changes from bottom to up which might be a challenge.
Any...
Hi
I`m trying to create two points on a spline curve at the 33% and 66% of the spline lenght
I use Point Set - Curve Points and Curve Percentage Subtype.
It creates points but when I later on divide original spline with created points -> divided curves are not equal.
Even when you look at the...
I looked for this problem and it seems that someone has already asked it on a forum but unfortunately didn`t get an answer
The problem is with offset curve in Sketch environment. I projected some curves into sketch and wanted to offset them. I get a message saying "Offset is not well-defined...
Hello
I`m trying to find a feature which allows me to check how the section ( mm2 ) of the pipe changes along the guide curve ?
I have a Swept feature. One section at the beginning and one section at the end. I created a surface using these two sections and a guide curve. I used Scalling...
Hi
I`m using NX10 and trying to make a Swept which will be tangent to first, and last section ( similar to Through Curve Mesh where you select surfaces to be tangent with ) and also I want to control its shape by a spine curve ( spine curve is perpendicular to first, second and last section )...
I have an assembly with two parts. In one part there is a point. In Expressions I have p1143_x = 5 p1144_y = 10 p1145_y = 15
In another part ( in the same assembly ) I have two curves and an angle between those curves is for example p1200=20
How to set up a value of an angle ( p1200 )...
HI
Anyone who could help me with some source code for compiling a program?
The function should be like this:
The 3D-model part file contains some points.
These points is manually selected, one by one, from the modeling.
The grip program should output the X, Y and Z coordinates drawing table...
Hello
I would like to make an assembly for example sth like this
top.prt
working.prt (attributes: "height=100")
electrode_1_working.prt (attributes: "startpoint=height+5")
electrode_2_working.prt (attributes: "startpoint=height+5")
Is there is any function that I can put...
Hello
I would like to make a few groups of tools in Machine Tool View. Every group of tools will be for a different material. And how to connect it with "Create Operation" window like in the picture ?
Hello
I`ve got a problem with wraping a curve on cone. I would like to make cone like in the picture and I`m wondering about the best way to do it. Wrap a curve on cone then sweep a circle along guide ( this wraped curve ) and then substract. Could anybody show me how to do it ?.
Hello
Has anyone have any problems with moldwizard after qrm3 installation ? I`m wondering about installation it but I heard that are some problems with moldwizard, is it true or is it safe to install it ?
Hi
I want to make something like a wire from old phones, and I need to sweep a circle along helix in 3D. I tried to draw a helix using "radius method - use law" but I don`t know that this option could draw a helix in 3D. Maybe somebody had some ideas how to make it or some tricks ? I`m using...
I need to create a tangency joint between two solids. One of them is a cylinder (2) and another one a complicated solid(1). I want to create a tangency between a cylinder face and faces of second solid (3). Cylinder is fixed to ground, solid (1) is moving like in a picture ( A and B ), also...
