Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: Mr168
  • Content: Threads
  • Order by date
  1. Mr168

    Washer to fill a countersink?

    I have a bracket that currently fastens using a pair of 3/8-16 flat head socket cap screws with what is presumed to be the standard 82 degree taper, so the bolt holes on the bracket are countersunk. I need to mount a spacer to the face of the upper bolt hole, and need a flush/flat surface to do...
  2. Mr168

    Bonding Carbon Fiber Airfoil Halves

    I have a small extruded airfoil I am looking to duplicate in carbon fiber (amateur garage setup). It is 6 feet in length, but with only a chord length of about 2 inches. I am looking at duplicating using a two part mold and wet layup with vacuum bagging (for the sake of this discussion, I am...
  3. Mr168

    Practical limit to bump steer adjuster length?

    In a road-racing only situation (I know, this is a "bring me a rock" question with respect to variables, so hoping someone has feedback of collective experiences or "conservative" values), is there a practical limit on the length of bump steer adjusters, i.e. lowering the connecting point of the...
  4. Mr168

    Fastener Supplier?

    I suspect I already know the answer, but is anyone aware of a supplier who manufactures an allen/hex drive button head sheet metal screw in stainless steel? I have found a single supplier for the RC car/plane industry, but they were available in black oxide finish only. I have located the...
  5. Mr168

    Exhaust blown diffuser options

    A question for my Eng-Tips automotive brethren! Background: Hill climb/time trials car. Car has a front air dam and splitter, radiator ducted through the hood, flat undertray extending back to approximately the firewall. Rear wing with large end plates. Less than ideal exhaust piping...
  6. Mr168

    Supplier for aluminum airfoil extrusions?

    Is anyone familiar with a supplier who sells small quantities of aluminum airfoil extrusions (1-2 meters in length approximately)? I am on the hunt for a LNV109A profile extrusion, but am willing to experiment with other race wing profiles for an underbody application. I have managed to...
  7. Mr168

    Consulting and the Affordable Care Act

    I'm curious as to the thoughts of the Eng-Tips community as to whether we will see the Affordable Care Act have a significant impact on the Engineering Consulting industry. For a moment, lets put aside the turmoil associated with Obamacare, and operate under the assumption that the ACA won't be...
  8. Mr168

    Front splitter end plates

    In looking at some of the most successful hill climb and time attack vehicles, those running substantial front splitters as part of their aero package frequently have very large end/spill plates on them. Key examples would be the Peugeot T16 at this year's Pike's Peak, and several variations of...
  9. Mr168

    Induction PWHT Equipment?

    Does anyone here have any recommendations or negative experiences with various manufacturers of induction PWHT equipment for field welding applications? We have a project in the works where the times and temperatures involved lead us to anticipate too many ceramic heater burnouts, and...
  10. Mr168

    High Temperature Purge Dam

    Is anyone aware of any soluble purge products that will withstand elevated temperatures, i.e 600°F minimum? We have a closure weld at a nozzle that must be back-purged, and the nozzle is not of sufficient length such that we can get a paper purge in without burning up the dam. Being a...
  11. Mr168

    GMAW-P on P4 Material

    Does anyone here have experience using a pulsed GMAW process on P4 (Gr. 11, 12) material? Using Lincoln equipment and running a downhill technique, we were unable to get a porosity-free weld using ER80s-B2 wire and a 90/10 Ar/CO2 mix. When running the same process and comparable parameters...
  12. Mr168

    Welding P91 to SA-106 Gr. C

    Aside from the issues with carbon migration and PWHT, what are some of the other negative considerations when joining P91 and carbon steel (SA-106c) materials? While we are forced into a current situation in which we are required to make a series of these welds, I am looking for further...
  13. Mr168

    D1.1 with foreign equivalents

    I have three materials at hand, JIS-SS400, Q435, and Q235 all for a basic structural application. The vendors supplying the steel have been less than cooperative thus far. I have yet to find any information other than their basic composition tying them to a UNS number or ASTM equivalent...
  14. Mr168

    P91 Weldability Issues

    We are having issues with all of our P91 pipe spools. The spools supposedly have their end preps machined by the supplier after furnace PWHT. Deoxaluminite primer is applied to the end preps prior to transport, supposedly after PWHT and prior to shipping. In the field, we are having...
  15. Mr168

    PWHT of Weldolets in B31.1

    This is somewhat of a debate between our home office and fabrication facilities at the moment in regards to the correct interpretation. I can't find much of the Bonney Forge documentation that has been referenced in older threads, most of which refer to B31.3 criteria. In B31.1, how is the...
  16. Mr168

    RT Source Size?

    Does anyone know what aproximate dimensions would be for a 60 curie Cobalt 60 source? I was doing some unsharpness calcs using our Iridium size for our heavier wall, and we're teetering on the ASME limits with .068. I was under the impression that the source size for Co-60 was a bit larger...
  17. Mr168

    High-Temp Inspection Camera?

    On some of our heavy walled pipe, we're looking for a borescope-style inspection camera that we can snake in through the gamma plug to take a look at our welded root passes. The problem is that we'd like to be able to do the inspection without pulling off the 400 degree preheat. We looked...
  18. Mr168

    Governing code for micropile welding

    Would the welding of a bearing plate to the top of a micropile casing fall under D1.1 jurisdiction, or is it covered somewhere in ACI? The governing code isn't listed on the subcontractor document, and we're awaiting the result of an RFI we submitted, but we'd like to make sure we have the...
  19. Mr168

    STT for power piping?

    Is anyone familiar with any success stories involving the Surface Tension Transfer process for power piping? The non-technical corporate big-wigs are butting in yet again, and trying to run our narrow groove orbital off an upcoming project, despite great success as of late, with their...
  20. Mr168

    D14.4 Welder Qualification

    Under AWS D14.4, if a welder tests on a joint combining group 1 and group 3 materials, is he qualified to weld G1 to G1 and G3 to G3 as well? 7.18.1 just states that he needs to be qualified to weld each group.

Part and Inventory Search