Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: qwicker
  • Content: Threads
  • Order by date
  1. qwicker

    WB nodal positions?

    Hi all, Using WB 12, how can I grag the nodal positions for an area? For example, in classical, I select the particular area, then select nodes attaced to that area. I am interested in knowing the undeformed positions, and then the deformed position (displaced). Thanks in advance!
  2. qwicker

    DesignModeler "Glue"

    Hi all, I'm just starting out using DesignModeler with workbench 12. I know the classic version very well, and I am looking for the "glue" command. It seems that I am looking for Connect in DM...When I use this command it seems to connect the areas OK but I dont think the lines and nodes are...
  3. qwicker

    Re-mesh with contact pairs?

    Hi all, I have a relatively simple question. I have a large model with many contact pairs. I need to remesh one of the volumes because I am not happy with the way the model runs. If I remesh the volume, will all the contact pairs associated with that volume's areas update? If not, can I...
  4. qwicker

    Identifying 'bad' element?

    Hi all, I have an analysis running which seems to be getting stuck on 1 particular element. The output indicates "1 U-P ELEMENTS DO NOT SATISFY THE VOLUMETRIC COMPATIBILITY" I am not so much concerned about the message because I encounter it all the time with hyperelastics. However, is there...
  5. qwicker

    U-P elements

    Hi All, I have a working model which achieves convergence, but I keep getting multiple convergence iterations on some load steps. XX U-P ELEMENTS DO NOT SATISFY THE VOLUMETRIC COMPATIBILITY Is there anything I can do here aside from just stepping the load smaller? Small load steps work...
  6. qwicker

    Questions for the experts!!

    Hi all you expert Ansys users, I was hoping to get some feedback on one of my models that I am running. I have a working model, and I am confident in the results. However, I have many models to run and the run times are quite long (in my opinion). I was looking for some thoughts, comments...
  7. qwicker

    Pivoting???

    Hi all, I am running an analysis and I keep getting a warning saying " Pivoting option activated for Sparse Direct Solver. The memory required may greatly exceed predicted amount. In that event rerun with increased memory using -m option " Because of this the solver always...
  8. qwicker

    Distributed Ansys

    Hi, I am currently learning how to use Distributed Ansys as we have upgraded our computing system. However, the biggest issue I seem to have is that I cannot monitor my solution progress. When using the GUI or batch mode, there is no output window like regular Ansys so I have no idea how far...
  9. qwicker

    Load Step clarification

    Hi everyone, This is basically just to clarify my understanding of the load step. I have a part which undergoes large deformation very quickly with virtually no load. The simulation is a metal cable bending around a large cylinder. The cable starts as tangent to the cylinder then a downward...
  10. qwicker

    2D contact & deformation

    Hi, I am trying to model the contact deformation that occurs when 2 parts mate. I have constructed my 2D model and have created a contact surface between the lines that are going to be making contact. Basically my simulation has a sharp corner (say from a rectagle) hitting the side of another...
  11. qwicker

    Material Models Database?

    Hi, I was wondering if anyone knew any places to get raw data for standard materials. For example, I am trying to investigate contact deformation of Steel 4340 (standard material) but the stresses get way to high for the linear models that Ansys accepts. I have used the TB command before and...
  12. qwicker

    Rubber Modeling

    Hello All, I am going to be modeling some rubber parts in Ansys for compression testing. I have no experience with these materials, and am completely unfamiliar with what material models to use. The material will be natural rubber. I appreciate any guidance. Also, even more helpful would be...
  13. qwicker

    Modeling Hardness

    Hi, I want to model a material (tool steel) during compression testing. Is there a way to put in the hardness number into ansys? I have 2 different variations of the same material with the same Modulus, but different hardness numbers. How would one go about that in ansys? I tried to search...
  14. qwicker

    Animate?

    This *should* be a very simple question. I am just animating over results for my part and everything works fine, and I can save it to an AVI file. The only problem is, I cannot view any sort of scale so the animation is almost useless! I tried googling this and looking through my manuals but...
  15. qwicker

    Large Plastic Deformation

    Hello. I am modeling a 3D part (can only be done in 3D). I am applying a large tensile load which I know will exceed the yield point of the material(AlNiBr). I want to plug in the data points for the stress-strain curve in the mat'l properties as "nonliner multilinear elastic". However, the...
  16. qwicker

    Ansys Contact

    Hello, I am using Ansys to model some simple plates, and I keep getting a DOF error. I know what it typically means, but for some reason it is connected to my contact area. Let me explain. I have 2 circular plates with holes in the middle. They are stacked one on top of the other. The...
  17. qwicker

    External Pressure on half of a PV

    Hello, For those who read my last thread, I have completely solved it. Thanks to those who helped. My new quesion is merely conceptual. I have a pressure vessel with an internal pressure that will have only HALF of its external shell subjected to a very high external pressure. I am not...
  18. qwicker

    Press Fit vs. Shrink Fit

    Hello everyone. This is my first post, so bear with me. My project involves fitting a solid shaft of Beryllium Copper (BeCu) into a BeCu sleeve. I am trying to figure you the best method to do so. My calculations are a bit rusty so I am not sure if I have done this correctly. I suppose the...

Part and Inventory Search