Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: gregfox
  • Content: Threads
  • Order by date
  1. gregfox

    Datums BC Sometimes A

    On a simple bock with a hole or boss, I’ve seen three datum references ABC and a single positional tolerance. I understand the need for the xy placement tolerances of B and C relative to the two side planes, but not the top surface A. Obviously a feature has to be on the surface referenced as...
  2. gregfox

    Circularity of Holes

    After reading so much gd&t stuff, it has become apparent that no vendor is capable of accurately drilling a straight hole with a single diameter, what are commonly held tolerances to be applied to holes that are: drilled drilled and reamed made with an endmill Or is it only for pocketed...
  3. gregfox

    Tubing Snap Fit

    Tubing Snap Fit I wanted to make a plastic (Polyethylene, 0.09” thick) snap holder for some tubing (0.625”). It would be hand pressed on, and be allowed to be easily removed. The snaps would be similar to “C” shaped holders for ratchet tools or a Saddle foot chair glide on a tubular chair leg...
  4. gregfox

    Sheet metal sides overlapping and trimming

    I'm making an angled air shoot tube that has a connecting square that fits into a square output tube. The top of the shoot angles down from the connecting square What I have is essentially an 10" extruded "n" channel. Both sides of this "n" have a cut 2" from the connecting square end, forming...
  5. gregfox

    Molded Corner Boss

    I have a box with a boss in one corner (some distance from the wall), and I’d like to add two ribs (tangent to the outside of the boss OD, and each perpendicular to the inner wall of the box. I extruded the box and boss with a 1 degree taper. My question is how to draw the sketch for the ribs...
  6. gregfox

    GD&T MMC versus Tolerance

    I understand the difference between the position of a feature and its size. I would like to know why GD&T MMC (or LMC) is use for a hole and pin rather than just making the dimension of the hole and pin such that they will always fit if in tolerance. I'm really not getting this "bonus" thing...
  7. gregfox

    Packaging Design, Blister Pack Snaps

    What are the general design considerations for blister packs: Tolerance between male and female halves Tolerance between male and female locks Fox Manufacturing Group (Machining and Molding)
  8. gregfox

    Packaging Design Blister Pack Clamshell

    What are the design considerations for blister pack Clamshell: Relative dimensions for the hinge area and distances from the two halves etc. Fox Manufacturing Group (Machining and Molding)
  9. gregfox

    Defining the Thread Start Angle in SolidWorks

    Good Day, I try to write out processes that I tend to forget in SolidWorks. Some of which I just seem to keep having to mess with the parameters to get it right. For some reason, I’ve had issues with how to orientate the drawing for forming threads so that they start at the top of a tube etc...
  10. gregfox

    Assembly to Subassemblies

    I have built up a system in an assembly. It contains all discreet parts, all started from the assembly. These can be grouped (and for ease I have group them in folders in the assembly tree) as Outer Tank, Module, and Lid. Two questions: Can I make a subassembly with all the same links and...
  11. gregfox

    Subassembly modification

    Say I am building a box out of separate parts (not molded). I would have bottom, sides, and front and back. I would like to radius the sides of the finished box, but the parts files should remain non radiused. How is this done. Ideally too, I would like a subassembly of the fabricated box with...

Part and Inventory Search