My company plan to set up a sub-zero process capability and get the Nadcap certificate. I know the equipment should follow the AMS2750D, it means TUS ans SAT must be meet. but I have no idea about the detail equipment specification of the freezer. Most of my friends just have the experience in...
The best vacuum level I need is 1 X 10 -3 Torr.
But I jsut found that I made a mistake, it was written as " 1 X 10 -3 Torr Range" in the contract.
Will someone heip to let me know what the difference in between?
Does the supplier still have to meet the best vacuum level?
if yes, where I can...
please help to provide some information below.
what is the difference between the Fixed thread ring gage and the adjustable ring gage?
How do I know which one will be the best to be used/purchased?
Is the calibration method can be a problem?
Thank you.
Grinding problem – can’t meet Roughness 0.2 micro mm
I had a problem in grinding operation. Is anybody can help me to provide your comment?
Material: AMS 5659 (H1025) Corrosion Resistant Steel
Dimension: (in mm)
Before grinding: 11.40 Dia X 8.20 Dia
Specification requirement:
11.20 Dia...
is there anyone can give me the definition or explaination about the terms below:
Shell Press
multi die
multi die tooling
die shoe
conversion press system
RPT
SOT
thank you.
Is somebody can help me to confirm the following:
A UNJF Ring Gauge can be used to inspect the component's UNF External Thread.
A UNJF Plug Gauge can not be used to inspect the component's UNF Internal Thread.
Thank you.
For Grinding, Lapping, Honing, Polishing and burnishing, they all make a good surface finish and just remove very little amount of material. Will somebody can help me to provide their exact definitions and the differences in between.
Thank you for your help.
As I know, the term of Deep Hole Manufacturing is according to the ratio of the Diameter and the length of the hole to be manufactured. If the actual ratio value is smaller, then it can be named as Deep Hole manufacturing but a common machining or drilling.
I can’t remember this ration value...
I am new in calibration. A customer asked me what ANSI standard do you use to calibrate the caliper, micrometer, depth gage, etc., I can't find the answer from the internet. What I do is according to the supplier’s spec. or catalog.
Is anyone can help me? Tell me the ANSI Spec. # for different...
A Drive Shaft is going to be measured, but there are some considerations that I don’t have the answers yet and don’t know if the measuring method I planed is correct or not. Please help me to provide the answers or your suggestions.
Drive Shaft Description:
Overall Length: 380 mm
Diameter A...
1. What is difference between Runout and Concentricity, esp. just want to get a coaxiality.
2. Does Runout applied on rotating part only? If not, then I thought it is same as concentricity. Am I right?
Hi All,
I'm not familiar with the Material Test.
One of the customer is asking a test.
Material is cast steel CF8,
and the requirements as following:
Tensile Strength : 485 MPa
Yield Strength : 205 Mpa
Somebody told me that the NO. of specimen should be selected first. Does someone can...
Hi All,
One of our customers asks me to do the Gage R&R on a sheet metal part. One of the critical requirements is Flatness. We know that flatness (.008 inch) may be inspected by CMM(program and non-program) or manually with indicator. I thought that this may not a good idea to do the Gage R&R...
As I know, ASME Y14.5M-1994 is a complete GD&T Spec., but ISO's GD&T is splited into many ISO specifications.
Is any boby tell/provide me the whole ISO specification NO., which related to GD&T? And What are the differences between these two GD&T specifations? Or where I can find the answer.
Hi,
I’m new in this Forum. I have a tapping problem, hope somebody can help me.
Problem: may have one or two enlarged taper hole on the far side after taping.
Material: Al 5052 H112, Thickness: 12 mm
Assignment:
Taping (through) (21) M3 Threads, (38) M4 Threads, (52) M3 Threads
Machining...
