Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: GregPerry
  • Content: Threads
  • Order by date
  1. GregPerry

    Asset Management Standards

    I am looking for specifications or standards on the following asset management items. 1. Equipment functional analysis, criticality analysis, FMECA's. 2. Spares criticality analysis and stock holding levels. Greg
  2. GregPerry

    Tempered Martensite

    According to literature the following steel: BS 970 817M40 Condition 'T' should have a final microstructure consisting of tempered marensite. We have had a fatigue failure on a solid shaft and testing revealed the following: Chemical properties all within specification Mechanical Properties...
  3. GregPerry

    Stress concentration due to taper locking element

    Hi Does anyone have any reference to what stress concentration factor (Kt) I can apply to a taper locking element fitted to a solid shaft? I need actual values not assumptions please if that is possible. Thanks Greg
  4. GregPerry

    Stress Consentration due to taper locking element

    Hi Does anyone have any reference to what stress concentration factor (Kt) I can apply to a taper locking element fitted to a solid shaft? I need actual values not assumptions please if that is possible. Thanks Greg
  5. GregPerry

    Extracting Oils from Organic Material

    I would like to know how to extract oils from organic material. I would like to set up a little system at home where I would be able to extract oils from leaves, flowers, etc... I would appreciate some ideas on what process would be involved. Thanks
  6. GregPerry

    Seperating the cream from the milk

    Anyone know how a cream seperator works? I have a small manual one and would like to know the theory behind its operation. Thanks
  7. GregPerry

    Cross refernce for materials

    Is there a web site where I can cross reference material specifications: e.g.: If I enter werkstoff no. 1.7225 I can get a list of all the possible equivalents. Greg
  8. GregPerry

    Determination of Fracture Toughness

    Dear all, 1. Can fracture toughness be determined from Charpy Impact Values? If so what is the formula recommmended. 2. Does anyone have fracture toughness values for the following shaft materials: EN24 'T' EN26 'T' Thanks Greg
  9. GregPerry

    Fatigue failure of low stressed shaft

    We have a number of gearboxes installed in 1991, since then 10 shafts have failed by means of fatigue. The failures happen at two positions. I have calculated the following stresses based on the material and shaft geometry: Position 1: Stress = 67 MPa, Endurance Limit = 82 MPa @ 10^6 cycles...
  10. GregPerry

    Risk Analysis

    I have to draw up a Risk Analysis for mechanical equipment, i.e. determining the risk of a failure and its impact on the machine, the system and possibly human lives. Does anyone know of existing processes or have any references. Thanks Greg
  11. GregPerry

    Fracture appearances of fatigue failures in bending

    I am looking for Charles Lipson's table of "Fracture appearances of fatigue failures in bending". Book references or web sites. Thanks
  12. GregPerry

    E44CP Pulviriser Gearbox

    1. We are wanting to replace a gearbox on an E44CP Pulveriser that was manufactured in 1972. To do this we need to know what thrust is exerted on the gearbox. If anyone has knowledge of these machines please help. 2. If anyone has a E44CP Pulveriser that they have scrapped or are wanting to...
  13. GregPerry

    4 x bevel set frequency only

    I have a 2 stage gearbox and a vibration consulatnt has measured a 4x bevel set frequency (first or high speed stage of the gearbox)in the vertical direction only. All other frequencies 1x, 2x and 3x are all very low. The 4x has a a RMS velocity of 11.23 mm/s. Any idea as to what this could be...
  14. GregPerry

    Oil Cleanliness Levels in Industrial Gearboxes

    I am looking for as much information as possible on oil cleanliness, interpretation of oil analysis, etcc...Applicable to industrial gearboxes and bearings. Thanks, Greg
  15. GregPerry

    Oil Cleanliness in Industrial Gearboxes

    I am looking for as much information as possible on oil cleanliness levels, oil analysis interpretation, etc... Applicable to industrial gearboxes and bearings. Thanks Greg

Part and Inventory Search