Search results for query: *

I have a plate that has a constant thickness of .500". However I have a maximum and minimum length and width I can use in my application. I created the plate with two length parameters with multiple values one for length and one for width. I can select the parameter and choose in a drop down...

I am attempting to do a join of a surface model in Catia V5 so that I may convert it to a solid model. After recreating surfaces and retrimming surfaces I tried to join the surfaces and got the following error message. Incoherent Join Specifications: Selected elements have not the same...

I am trying to create an assembly with a pin and a solid to remove that represents a C'bored hole subtracted from a solid block. I want to be able to rotate the C'bore by what ever degrees I choose. I have created a rotation line under construction geometry that is Angle/Normal to curve. I then...

I am new to Catia so this may be a simple question. Is there a way to replace a component in an assembly using the replace command and have that new component come in and maintain links to parameters or formulas within that assembly?

I am new to Catia V5 and in the process of creating a parametric assembly. This is one of the many problems I have encountered. Loop design between geometry and constraints. Can anyone tell me what this error means exactly and how I may get around it.

I have an assembly that has gone from Cadkey to SolidWorks and now my Supervisor wants this assembly detailed in Catia V5. I exported for SolidWorks as an .iges file and opened in Catia V5. Under the compatibility iges tab I selected map 308/408 iges entities onto a products structure because I...

Here is my problem I have a tapped hole location that is offset from a drilled hole positive x .625 I am trying to change the offset from the positive side to the negative side. What I tried was typing 0.0000394 to move tapped hole to center of drilled hole or equivilant of 0.000 and next typing...

How do I measure from the base of hole at its lowest point where it breaks through on a contoured surface to the start of the hole? I want to create a cbore that is 1.450" from the base to the lowest point of this contoured hole. When I use the measure tool I only get from the highest point of...

I am trying to create a custom Esize border 72" x 36" When I go to custom size and place these sizes in the sheet size increases however the border dissappears. How do go about creating the size above with the border included?

Can I do a mimimum distance check with accuracy? For example from a part shape or surface to the end of a drilled hole feature. I have a Ø.281 ball drilled hole that I want to stay a minimum distance of .250 from the nearest part shape. The hole was created with the hole wizard. The part shape...

I am trying to trim a pin to a contoured surface in my model with out success. The pin was created using the revolve sketch command. The cut with surface icon is available but once i select it I cannot select my pin or surfaces around it. There is also a clearance hole through the part for the...

How do you go about adding a jpeg to a post for clarity. I think it will show what I am trying to accomplish?

Here is my problem, if I create a top view in my drawing with the origin in the center I can never select the origin in the hole table panel. I go to hole table under datum I highlight origin and go back to my top view to select the origin however I cannot select said origin. I have to sketch a...

Is there a way to get a ball drilled hole besides the way I go about it? Here is what I have been doing to get the ball drill results. I change the drill angle on my drilled holes from °118 to °180 which makes the bottom flat. I then go in and create a fillet say of .25 for a Ø.500 ball drill...

I have one model for two drawings and I suppressed certain features so that on sheet1 I show only the lathe work I want done. However when I go to sheet2 it shows the same contents of sheet1. Is there a way to dissassociate the various sheets from one another so that I can use one model for...

Is there a way to edit a TAG ID in a hole table? As an example I selected 4 features and they were labeled under TAG as A1,A2,A3,A4 in the chart and on the drawing. I would like to change the id to E44,E45,E46,E47 is this possible?