Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: bryjarmoc
  • Content: Threads
  • Order by date
  1. bryjarmoc

    Using IPAD for Floor Inspection

    I heard there was an aerospace version of this called "ISquawk". Does anyone have knowledge of any app/software like this? Would be similar to what a Home Inspector would use when doing a house inspection. See the defect, take a picture and then come back after the defect is repaired and...
  2. bryjarmoc

    Inspection Using APPS with IPAD

    I work for an Aerospace manufacturing company. We build part for Boeing, Spirit, Cessna, Gulfstream, Airbus, etc. We are trying lean out our inspection system. Currently the process is extremely manual. I saw an APP on my IPhone that was for inspectors that inspect properties (homes, real...
  3. bryjarmoc

    Justification of Manufacturing Engineering for a Company

    I work in a company that builds aerospace product for OEMs (Spirit, Textron, Boeing, Gulfstream, Airbus, Northrop, etc) We have "planners" and we have machine programming. We do not have anyone really focus on Manufacturing Engineering principles. ALL engineers are under "ENGINEERING", but...
  4. bryjarmoc

    Camio CMM Software

    [indent]Does Camio CMM software have the capability to report/export the XYZ nominals/actuals as well as the ijk (vectors) nominals/actuals?
  5. bryjarmoc

    Is Dry-Lube a finish?

    The specification we are dealing with come from Boeing. The specification states that ALL dimensions are BEFORE finish. The ID of the bearing is coated with .0002-.0005 dry lube. The before dry Lube diameter is .9995-1.0015. IF dry lube is NOT a finish then the end diameter would be in the...
  6. bryjarmoc

    Machine Shop Operator Inspection Frequency

    Not sure if this is the right place to post this... but here goes. I am a QE developing standards or (best practices) procedure for Machine Operators (Lathe, CNC Mill, Manual Mach, etc). One of the aspects is inspecting the parts that come off the of the machine throughout the run. Does anyone...
  7. bryjarmoc

    DCC Alignment with Zeiss Calypso

    We have a Zeiss CMM with Calypso software. I had some experience on a B&S using PC Dmis software. In PC Dmis when you wanted to run multiple parts you would run the manual alignment on the first part and then after that you did not have to do any more alignments as long as the succeeding parts...
  8. bryjarmoc

    Dimension Problem

    I am not sure if this is the correct forum to ask this. See attached picture. I am trying to find out the dimension of "X". If anyone knows the formula for this please let me know. Thanks
  9. bryjarmoc

    Concetricity with .002 of T.I.R.

    (see attached view) What exactly are we measuring with this callout?
  10. bryjarmoc

    Thread Issue

    We have the following issue: We have a shaft Outside threads. The Go Gage will not "GO". However, the parts fit to the mating part AND the mating part checks "good" using Thread Plug Gage. How can this happen?
  11. bryjarmoc

    Implied Centerline

    (see attached figure) The only requirement on the print for the keyway is the width and length (from opposite side of ID to flat of keyway). here are the questions: Is this keyway "implied to be on center"? If so, what would be the tolerance? If engineering does NOT need the keyway to be on the...
  12. bryjarmoc

    Mistake Proofing.

    I work in aerospace industry. Obviously we do A LOT of drilling and riveting. My question is that we have a high reject rate for Counter sinks being the incorrect size. Are there any tools/devisces that would mistake proof the drill bit(s) to where it would virtually impossible to drill a bad...
  13. bryjarmoc

    Circularity tolerance (out of round condition)

    If there is not a "circularity" requirement on the the drawing then is there an "assumed" circularity tolerance on any given diameter. I.E. a percentage of the nominal size?
  14. bryjarmoc

    Zeis VS. DMIS based CMM's

    Our company is purchasing an Automated CMM. I have had experience in programming/operating Brown & Sharpe CMM's with PCDMIS software. It seems the Zeis "sales pitch" caters to the person that knows nothing about CMM's or programming of CMM's (more user friendly for the beginner). My concern...
  15. bryjarmoc

    Effects of the magnetizing of non-magnetic radial bearings?

    We build electromechanical motors (ac & dc). We are having an issue with bearings in a particular motor drawing "high amps" during testing. We have traced the issue down to the change in bearings. One of the questions that has been raised is "Could the bearings have been magnetized? If so...
  16. bryjarmoc

    Keeping dimension/flagnote Facing Forward while Rotating Model

    Bare with me as I am new to Catia software and UG software. Is there the an option to set up the "dimensional callout displays" to always face "forward" while the model is rotated? I want to capture the callouts in 2D, but when I rotate the model to show where a callout is "pointing" you can...
  17. bryjarmoc

    Display parameters to Rotate with Model

    Is there an option that I can put on so the Flagnotes, GD&T Callouts, Dimension, etc will rotate with the model?

Part and Inventory Search

Back
Top