Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: handee
  • Content: Threads
  • Order by date
  1. handee

    Temp Control for Hazardous Locations

    Hi folks, I haven't had any luck finding a free-standing PID tmperature controller (actuates a modulating cooling water flow valve) that can be located in a hazardous location. The operators will want to adjust the setpoint at will, and the non-XP control room is some distance away. Quite...
  2. handee

    Lab-scale in-line dynamic mixers

    Looking for a lab-scale version of a high shear in-line disperser or mixer, flowrate less than 1 gpm. Most models are much bigger than this. Anyone have any suggestions? TIA
  3. handee

    Estimating pressure drop of air in pipes

    Anyone have a good source to estimate pressure drop of air (atmospheric pressure) flowing through pipes (3" to 6" diam). My flowrates are only about 10-15 SCFM. TIA
  4. handee

    Aq. ammonia storage tank vent

    I'm spec'ing out a 5000-gal storage tank for a solution that is essentially 9wt% aqueous ammonia. Perry's says that for 9.5% NH3 on a hot day (at 90F) total vapor pressure can reach almost 4psia. Sizing the conservation vent is not a problem, I'll go with Groth or Protectoseal, but my plans...
  5. handee

    Storage tank breather vent valve

    Hi, we're desigining a 5000 gal SS atmospheric storage tank for non-flammable liquid. Well be filling it at about 100 gpm and draining it at about 30 gpm. I simply need a breather vent to let the air out when filling, and let the air in when draining (its a little smelly so we'll be venting it...
  6. handee

    Storage tank breather vent

    Hi - this seems like it coule be an extremely useful new forum! My application is a simple one - 5000 gal SS atmospheric storage tank for non-flammable liquid. Well be filling it at about 100 gpm and draining it at about 30 gpm. I simply need a breather vent to let the air out when filling, and...
  7. handee

    relief valve sizing calc

    Dows anyone have or know of any spreadsheets for calculating relief valve size for liquid service, or where to find information on performing the calculation? TIA! Fran McConville
  8. handee

    Costs of SS vs Hastelloy, etc

    Hi. I'm just looking for some ballpark figures for the relative cost of 304SS, 316SS, and Hastelloy for manufacturing chemical processing equipment and vessels etc. Just rough numbers...TIA! Fran McConville
  9. handee

    PID loop tuning

    Hi, we're trying to control a modulating steam valve to a using a controller that seems to have four tunable terms. Here are the current values: PbH 16.6 Intr 65 Rset 50 Driv OFF Question is, what are the four terms? I recognize proportional band, integral, and derivative, but what's rset...
  10. handee

    headspace vapor concentration

    This is pretty basic stuff, but I could use a sanity check if anyone has the time. I'm calculating vapor concetration in the headspace of a tank of solvent (MW=53.1, bp=78C, vp=83torr) at ambient temperature. At atm. pressure, the mole fraction should simply be 83/760, and using PV=nRT I can...
  11. handee

    Concrete containment dimensions

    Hi we're building a rectangular 2ndary containment for a roughly 700 gal system that needs to be 18" high and 10ft L x 5ft W. Is there a minimum wall thickness required (I was thinking only about 4" since this thing will only be used in an absolute emergency and it only needs to hold the liquid...
  12. handee

    Draining Condensate from Return-side Duct

    Hello, we've got an air cooler that consists of a cold water coil and a blower. The only place we can locate the coil is upstream (return, or suction side) of the fan, so I'm a bit concerned about corrosion if condensation droplets reach the fan. But my first concern is draining the condensate...
  13. handee

    High-Melting-Point Monomer Storage Outside

    Hi. I've been asked to look into converting a 10,000 gal underground storage tank for use with a flammable acrylic monomer with a freezing point of 16C. The tank was designed for much lower freezing liquids - this monomer will freeze in place here in New England. Does anyone have any...
  14. handee

    Schedule 160 pipe pressure rating

    Hi. I can't get my hands on a copy of the ANSI standards - can anyone supply this info? I need to know MAWP and burst pressure for 3/4" Sch160 304SS pipe. A copy of the applicable page would be tremendous! Thanks!

Part and Inventory Search