Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: Speedy
  • Content: Threads
  • Order by date
  1. Speedy

    PRO E - Assembly Mass Parameter

    What is the system parameter for the Mass Of An Assembly? &PRO_MP_MASS is the Mass parameter for a part and as such can be added to a Part Drawing in a note. What is the equivalent for an assembly. I want to add the mass of an assembly to an Assembly drawing. Cheers, SPEEDY BTW. I am using...
  2. Speedy

    Drawing Report for Assembly Family Table

    I have created an assembly which has a 'family table' with 4 different configurations. I want to creat a report in a table on a drawing where I list the 4 configurations and then list the parts in the assembly for each configuration. If that makes sense? I've used the system parameter...
  3. Speedy

    Pro E 4.0 Non-commercial to professional - drawing formats & templates

    I have just purchased "Pro/ENGINEER Wildfire 4.0 for Personal Use". I also use the professional version at work (4.0 also). I want to use all the templates / formats from work. It will open the Config.pro and *.dtl files ok, but wont recognise the 'drawings formats' and Part and Assmebly...
  4. Speedy

    "Measure" function - Wildfire 4.0

    Hi Guys, I have just started using Wildfire 4.0. It was Wildfire 2.0 before this. The problem I am having is with the measure function, as in " Analysis / measure ". I want to measure the distnce between two parallel surfaces on seperate parts. I find it very difficult to pick up a surface in...
  5. Speedy

    Copy "associated Drawings" when copying Part File

    I created a drawing but I unticked the "Copy Associated Drawings" by mistake. When I save a copy of the part file, no drawing file is created. How do I edit the original part file so that the drawing will be copied too? Thanks...[cry]
  6. Speedy

    Gas Metering Pumps

    Gas Metering Pumps - are there such things ? We have an application that requires 2 combustible gases (fuel gas and Oxygen)to be mixed in-line and then filled into a chamber where the mix is ignited. Not only should the volume ratio be accurately controlled but also the degree of mixing. We...
  7. Speedy

    Repeat Regions - Maximium Number Of Rows

    I am creating a BOM on a drawing using a table with Repeat Regions. There are simply too many parts in my assembly and the table continues way down past the drawing border. How can I divide the table in 2, one beside the other. That is - limit the maximum no of rows and then start a new table...
  8. Speedy

    Modelling Partial Penetration Welds in FEA

    Problem as follows; We have a large cast component which is the main part of a structural frame of a hydraulic press type machine. In service loads are high cyclic tensile, clamp unclamp etc. To save on cost & lead time it is advised that we produce the part from welded plates. Stress relief...
  9. Speedy

    System Parameters - Where do I find ?

    Question - 1 Anybody know where I can find a list of the System Parameters on Pro Engineer - Wildfire 2. Question - 2 I want to export a full level BOM all Parts & sub-assems)to Excel. Is this possible? If not, how can I do it on a drawing. I created a BOM on a drawing format before but it...
  10. Speedy

    Darcy Weisbach equation for pipe pressure loss

    I want to make up a spreadsheet that will calculate the friction pressure loss in piping for different gases. I found the 'Darcy Weisbach' equation but I have a few questions as follows - Can this equation be used for compressible gases. One source says valid only for...
  11. Speedy

    Elastomer for extreme high temperatures

    I require an elastomer that will survive at least a couple of hundred cycles in a high pressure combustion chamber. Peak temperatures of 2,000 C or more. It's application is to protect metal parts that bounce around when the o2/ch4 mixture is ignited. Am I asking too much? I have requested...
  12. Speedy

    Pro-E to Solidworks

    I work for a small company which is part of a much larger corporation. We have recently been told what we will be switching over to Solidworks from our current Pro-E. This seems crazy to me as we literally have thousands of components going back years that are all in Pro-E. What is the best...
  13. Speedy

    Formation of Nitride Oxide

    We have a process as follows; Methane(Town Gas or bottled Methane) and Oxygen are mixed and ignited in a chamber at high pressure, up to 25 Bar. The ratio varies and could be twice Stoichiometric, i.e. double the amount of O2 required. We have been told that Nitric Oxide is forming at high...
  14. Speedy

    relevant assemblies for each part file

    Is there an easy way to find all the relevant assemblies that reference a part. Similar, I guess to the Parent/Child option for features. We have an extensive range of numerous assemblies and part files. It would be great If I could simply open a part file and find out all the assemblies that...
  15. Speedy

    Threaded Holes in a Hole Table

    Is it possible to add threaded holes to a hole table. I've tried it - it doesn't seem possible. Straight holes are working fine for me. The help notes say that hole tables only apply to straight holes. I have a drawing with up to 70 holes on a flat plate, about 3/4 of these holes are threaded...
  16. Speedy

    Rotary Coupler

    I have an application where i want to feed 4 seperate water pipes and a common return to a table that is rotating on a central shaft. I require a ROTARY COUPLER that will fit on over the shaft, approx 100mm dia, and will feed the water through as the table rotates. I did a search but could only...
  17. Speedy

    Better material than EURONORM 1.4571

    I have a component made from EURONORM 1.4571 (aka DIN W1.4571). This is a Titanium Stabilized Austenite Stainless Steel. The application is a machined threaded part that acts as a shield for a thermocouple in a high temperature/pressure combustion chamber. The problem with the existing...
  18. Speedy

    Tolerance for Dowel Holes

    I want to specify a press fit dowel hole for an M20 dowel. I always understood that all dowel holes were drilled and reamed to class H7, i.e +0.021 -0.0 mm on DIA 20.00 I see that there are 2 types of dowels, h6 and m6. Values on dowel would be h6 = +0.0 -0.030mm for M20 m6 = +0.008...
  19. Speedy

    Prevent printing of 'Curves'

    When I print a drawing all the 'Curves' get printing also. How do I prevent this? These curves would be in revolved features etc. Thanks, Speedy
  20. Speedy

    Good Book on Combustion Data

    I briefly saw a very good reference book on the combustion properties of Methane/Oxygen and Hydrogen/Oxygen. This had values for peak combustion pressure for various pre-igniton pressures and mixtures. This is very relevant to the work I do so I would greatly appreciate any help on this...

Part and Inventory Search

Back
Top