Hi,
What will happen if 4/O and 240mm2 underground medium voltage 33kV cable is paralled? it's used as a part of overhead line 33kV at the beginning of the circuit.
Regards,
Eskim
Hi All,
Our existing generators are 11,000 V +/-5% output voltage. We set AVR 3% above nominal volt (11,350). Gens are running with voltage control set.
What do you think If a new gen 10,500 V +/-5% will be synchronized with existing system. It should run 8% over its nom volt.
Regards,
Sumadi
Dear All,
I have very basic question, but make me inconfidence regard to speeding up induction motor. The existing nameplate is 600kW, 3.3kV and 2965rpm. We have to upgrade the feed pump system by installing VSD to control this motor up to max 3400 rpm. (operating will be 3100rpm)
The question...
Dear All,
Please confirm me for this small confussion. Can I use non-insulated 600V terminal lug to be used for 11kV arrester circuit ? In my opinion Yes, since voltage will effect to insulation material only so for non-insulated doesn't matter.
Hi,
I am calculating 3-phase power with these datas, all value line-to-line:
Ia= 782.831 @184.8 deg
Ib= 792.247 @306.9 deg
Ic= 763.033 @66.4 deg
Va= 10.973 kV @0
Vb= 11.005 kV @119.9
Vc= 10.990 kV @240.1
3-phase Real Power = ???
Anybody can help me ? Thanks all.
Dear All,
Sorry if this question has been posted before, I have found 2 thread about E/F protection on D-Y transformer, but not cover my question below.
1. We have experience Hi-Z fault on LV(400V) O/H line which is supplied by 11/0.4kV Delta-Star with solid grounded pole XFMR around 50kVA. At...
Dear All,
I've problem above for the last two days. The six-pole, full wave rectifier have one diode and thyristor broken at the same time. We have over current and over voltage relay picked up at excitation control (V~4000V and I~40A).
My question:
1. Why the current and voltage at excitation...
Guys,
I am looking for transformer oil purifier equipment will be used to purify 19000 ltrs of oil contains.
Anyone could recommend Manufacturer of oil purifier, please forward ro me.
Thank you all.
Rgds,
Eskim
Dear All,
What is the based difference between AC and DC HiPot tester. When I test HV equipment e.g. Surge arrester, cable, generator winding, etc. What is the best method using ac or dc tester ?
Some one told me that mA is the "most important" to select DC or AC ? I didn't understand what...
Dear All,
I am not experience in T&D. But our transformer using Lightning Arrester on HV connected to transmission line. How to get proper spec of arrester for this transformer (theory, calculation, standars, etc).
Also the LA is connected with discharge counter(?) what is the function of...
All,
Our 5,1128 MW's diesel engines have Reverse Power Prot. setting of 0.04 x Rated MW, it used both to stop the diesel engine and open main circuit breaker.
Can I just open the circuit breaker not stopping diesel engine ?
Could you please explain me of the following scenario:
* With existing...
Dear All,
My friend has problem on 150KV trasmission line about 100km's voltage drop to 120-130KV.
The qustion:
- What is the main cause of this problem usually..all of lead, tower and distance are under rating
- Is there any technic of installing capacitors to correct the voltage drop on HV...
Dear All,
I just found out that on one of our Substation has wood partition to seperate Switchgears and fiber optic junction boxes.
Is there any regulation about this, because in my opinion this is a fire hazard.
If some one out there could advise me the regulation i would be glad and...
