Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. ausman

    Trumpf Tasc6000 parameter menu

    Hi, Can anyone help me Re the parameter menu is on the Tasc6000 control Even within the service menu there is nothing regarding parameters, more specifically just need to make a small change to an axis on the gauge Thank you
  2. ausman

    Parameter Changing

    When is cutting good check the chiller temp. Also do a nozzle tape shot when you know the cut is good. When it starts cutting bad check the chiller temp again (is it the same temp) When it starts cutting bad quickly check the check the nozzle shot again with tape (compare the good & bad nozzle...
  3. ausman

    Focus lenses

    E-z mounts are great, makes lens easy to clean & save a heap of cash. invest in a couple of them.
  4. ausman

    Cutting head started cutting at 14-15 mm above the sheet - Amada LC-2415 Alpha III

    Glad to see it resolved, what initiated unplugging JA6 to begin with? Was there another issue that you resolved in this fault finding process that you didn't note? Thanks
  5. ausman

    Cutting head started cutting at 14-15 mm above the sheet - Amada LC-2415 Alpha III

    From Amada documentation (there is no reason for me to doubt these values) This signal should be 8.9V at nozzle gap with 2.0mm, 0V with 1.5mm, -8.9V with 2.8mm Have you tried testing the head with the aluminium function selected? this function enables a slow response mode on the HS98. Might or...
  6. ausman

    Cutting head started cutting at 14-15 mm above the sheet - Amada LC-2415 Alpha III

    This signal should be 8.9V at nozzle gap with 2.0mm, 0V with 1.5mm, -8.9V with 2.8mm Check & advise Carefully Do this check, what happens? G32 R_ ; Z-axis follow mode ON G33 ; Z-axis follow mode OFF R_ indicates a nozzle gap amount. For example, when R=1.5, the nozzle gap is 1.5mm. When R=0.3...
  7. ausman

    Mirror Alignment on a Mazak New Turbo X48

    What exact info do you need?
  8. ausman

    how to change LC 3015BIIINT language settings

    If it's the newer control it's just a parameter. If it's the older AMNC control (just the touch screen panel) it needs a firmware update (very difficult) If you already bought it then you might need to learn Japanese, it's probably easier than getting the firmware files.
  9. ausman

    Problem with vacuum pump

    You need to vac it down to 2 torr, turn the vac pump off. Check it after 10 minutes, if the vacuum has not leaked more than 0.3 torr then it's ok. I would check the vacuum pump, that oil should not be there especially if the hose goes straight to the resonator cavity.
  10. ausman

    Aluminum Cutting?

    vladz21, If you can get you hands on a 3.75" lens you should try that, we have cut 1050 aluminium with pretty much the same settings as 5005 & did not have any of the issues you are seeing. Order the lens holder from Amada, about $300 or machine up a threaded spacer to lengthen the 5" lens...
  11. ausman

    Aluminum Cutting?

    One more thing, any chance the have the lens focal length mixed up? In other words could you have the 7.5" in the head instead of the 5". Check it please.
  12. ausman

    Aluminum Cutting?

    Correct convex come at the top. with the sot burr adjust your focus up 0.3mm then test cut, if it improves adjust it another 0.3mm & keep doing so until either it gets works or the cut is acceptable. If you still have the reflection problem then try & watch your power meter & see if the power...
  13. ausman

    Aluminum Cutting?

    Strange, I will ask a bunch more questions Did you see any evidence that the beam is actually coming our of the head and bouncing off the surface? Silly question, is your lens upside down? Are you using a single point nozzle? Can you please test again with a nozzle gap of 2.0mm Are you getting...
  14. ausman

    Aluminum Cutting?

    When you used the SS settings did you test cut an SS part then immediately try the same on a piece of aluminium without changing anything?
  15. ausman

    Aluminum Cutting?

    Check your focus again, on your other post the B Axis travel when you run your focus program seems too large. If your focus program only did 10 cuts and you start at B5.0 & ended at B15.0 that's incrementing 1mm per slit. It really needs to be 0.2mm per slit.(you might be a couple of mm out)...
  16. ausman

    Aluminum Cutting?

    Need more information, what's the background on the problem? Is the problem new, has the machine just been put in, are you a new operator? can you cut MS & SS ok? What can you tell me. Ta
  17. ausman

    Aluminum Cutting?

    Correct, we use 3.75" for most our thin material, but 5" works well too. Try pierce Pwr 3600, Freq 50, Duty 80, pressure 0.2,
  18. ausman

    NC FOCUS CHECK

    It the ability to use each of the 5 focal different setting in the AIVsetting page. If the function is on, the control will use 1 of the 5 values depending on which head number you have selected in the cutting data page(top right, 1,2,3,4,5) If the function is off then the AIV focal point...
  19. ausman

    Aluminum Cutting?

    Check your focus, you will probably never actually etch 1mm Ali on that machine, you will burn the optics & bellows from beam reflections. Use the shortest focus lens you have. the beam will bounce straight off the sheet if the focus is out too far. Pierce the sheet at pressure 0.2mpa & cut at...
  20. ausman

    NC FOCUS CHECK

    If you use 5nc focus function then enter the values 12.00 in the AIVSetting page in the related lens focus (2.5", 3.75". 5", 7.5", 10") you can set them all up if you wish) If you don't use the 5NC focus function then you set the 12.00 value in the parameter page under focus base position. cheers

Part and Inventory Search

Back
Top