Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Ronak_Patel

    commercial software for design of pressure vessel and heat exchanger according to ASME SEC ||| for nuclear application.

    Hello all, Is there any commercial software for design of pressure vessel and heat exchanger according to ASME SECTION 3 for nuclear application?? is there any code for design of storage tanks for nuclear application?
  2. Ronak_Patel

    ASME CODE STUDY STRATEGY.

    You can start by reading (1) companion guide to ASME (2) Book by Brownell & Younge (3) Book by Bednar (4) ASME PTB-4 (5)Book by Denis Moss (6) Code itself
  3. Ronak_Patel

    Impact Test Requirement for nozzle assembly as per UCS-66

    @r6155 client has not ask for any specifics. As per code, is my nozzle neck exempted from impact test requirement?? @Cobra17 UG-20(f) exemption is not allowed. @GD2 thank you for confirming. this seems bit counterintuitive though. Nozzle neck because of its own thickness is required to be...
  4. Ronak_Patel

    Impact Test Requirement for nozzle assembly as per UCS-66

    I have following configuration of nozzle assembly:- 1) Shell Material: SA 516 Gr 70 (Curve B) Thk :- 10 mm 2) Nozzle Neck Material : SA 106 GrB ( Curve B) Thk :- 6 inch ,14.27mm thk 3) RF Pad Material: SA 516 Gr 70 (Curve B) Thk :- 10 mm 4) Flange Material : SA 105 (Curve A) Size :- 150...
  5. Ronak_Patel

    governing thickness of forged neck welded to shell per UCS-66

    @YuJie_PV Since your nozzle neck is forged, shouldn't it be as per curve "C" {all materials listed in Notes 2(a) and 2(c) for Curve B if produced to fine grain practice and normalized, normalized and tempered, or liquid quenched and tempered as permitted in the material specification, and not...
  6. Ronak_Patel

    ASME VIII UG-44(b)

    @TGS4 Thank you for your response. In code case 2901, Fm value table note b reads "The designer should consider reducing the allowable factor if the loading is primarily sustained in nature, and the bolted flange joint operates at a temperature where gasket creep/relaxation will be significant...
  7. Ronak_Patel

    ASME VIII UG-44(b)

    code case 2901 was based on "Improved Analysis of External Loads on Flanged Joints PVP2013-97814" . @TGS4 is code case 2901-01 based on any paper??
  8. Ronak_Patel

    Reference material for API 650

    Thank you @Louisiana Inspector for your response.
  9. Ronak_Patel

    Reference material for API 650

    Hello, I`m new to storage tank design and i have started reading API 650. Can you please share name of any reference book or article for storage tank design based on API 650?? Is there any PTB/sample problem book for API 650? Any help on where to start for better understanding of API 650...
  10. Ronak_Patel

    Impact Test Requirement as per ASME SEC8 DIV3

    Hello All, As per KM-251 in DIV3 : "The Charpy V-notch impact values specified in KM-234.2 are established at upper shelf energy levels that are required for most high-strength, low-alloy steels. The designer does not need to provide any test information to use upper shelf correlations for...
  11. Ronak_Patel

    Older PVP Preceding.

    thread794-439631 Hello!! Im trying to find some older ASME PVP Proceeding online but unable to find any digital copy... Pls suggest way. I'm looking for 1995 & 1996 PVP Papers. Also, is there any way to contact directly to members on this forum??
  12. Ronak_Patel

    High Pressure vessel design using DIV 3

    @IdanPV Thank you for your guidance!!
  13. Ronak_Patel

    High Pressure vessel design using DIV 3

    Hello @Ariba01123 We cater to Oil & Gas, pet-chem and fertilizer industry. As of Now, we do not have any specific Vessel to design but my organization is preparing for any upcoming equipment specifically in hydrogen service. Hello @r6155, we are reading div3, but we wanted to understand more...
  14. Ronak_Patel

    High Pressure vessel design using DIV 3

    Hello All, We are trying to prepare Design philosophy of High-pressure vessels ( > 700 bar) using ASME sec8 div 3 in my organization. Please share any book, existing licensor or PMC specification for High pressure vessels Design for reference and guidance.
  15. Ronak_Patel

    Tema Interpretations

    thank you Christine74 and 0707
  16. Ronak_Patel

    Tema Interpretations

    Hello all, Is it necessary to be TEMA member to read TEMA interpretations ?? I tried searching for them on TEMA website but could not find any .. I need to search for Interpretations related to backing ring thk formulas .. If any one has it in PDF format, Pls share for reference.
  17. Ronak_Patel

    Design of Compression plate/Ring using brownell and young method.

    Hello all, I`m trying to Design Anchor chair for pressure vessel using Pv elite software . Pvelite is using Brownell & young method to calculate compression/top ring governing moment and thk. As per sketch 10.6 in book , 'l' is measured in Y axis , 'a' is distance from origin in Y axis where...
  18. Ronak_Patel

    Distortion of 106mm OD , 14mm thk nozzle during weld overlay.

    Thank you all for your response!! @Christine74 Yes ,it is SA-336. @EdStainless yes ,5mm is total w.o thk
  19. Ronak_Patel

    Distortion of 106mm OD , 14mm thk nozzle during weld overlay.

    How likely distortion will happen in 106mm OD , 14 mm thk base metal Nozzle made up of SA 366 F11 CL3 during weld overlay (inconel ,5mm )? is there any min base metal thk requirement for weld overlay to avoid distortion during weld overlay ?
  20. Ronak_Patel

    Does SB 171 UNS C44300 uses Arsenic as inhibitor or tin ?

    Dear all, SB 171 UNS C44300 has 0.8-1.2% tin and 0.02-0.06 % As , but the trade name for SB 171 UNS C44300 is Admirality, Arsenical so Does SB 171 UNS C44300 uses Arsenic as inhibitor or tin ?

Part and Inventory Search

Back
Top