Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. smurali1

    Corrosion protection for sea freight

    I am interested to know safe (for rust) way of transporting gear box from Europe to India. During testing of the GB the oil splashes all over the interiors of GB and lubrication happens. The oil is drained after testing and only a film of oil remains on the internal parts. Can this film...
  2. smurali1

    Graphite erosion from cast iron

    Hello Unclesyd, I note your point on high velocities will lead to to leaching. My concern still is why do we get blackish color when we rub our finger - even after washing!. Rubbing of finger does not apply much force Thanks SPM
  3. smurali1

    Effect of graphite particles

    Hello, What is the effect of graphite particles (coming out of machined cast iron) on the gear box life. Please note that we do hot alkali wash the cast iron part before assembly. However, the black color is still seen on some places on the surface. We need to use tissue paper and manually...
  4. smurali1

    Graphite erosion from cast iron

    Hello all, We are using a Cast Iron housing which has a machined hole. We pump lubrication oil through this hole. Will there be any erosion of graphite from the cast iron and will it get mixed with lubricating oil. I have this doubt because, if we rub our finger over machined surface, the...
  5. smurali1

    Manganese Phosphate coating presence

    Hello redpicker and corypad, Thanks for the feedback. The case is of first type i.e. to check presence of Manganese Phosphate or no coat. Let me explain some more background: We assemble Manganese Phosphate coated part with slight interference on to a shaft. We see some powders (presumably Mn...
  6. smurali1

    Manganese Phosphate coating presence

    Hello all, I am looking for a chemical test which will help me to detect the presence or absence of Manganese phosphate coating on steel part. Your feedback please. Thanks smurali1
  7. smurali1

    Exploded graphite in SG Iron casting

    We have some SG Iron castings. We found exploded graphite formation in some of the castings after machining. (The confirmation was done by destructive study of one casting) Are there any NDT method to find out how much depth is exploded graphite? Thanks SPM
  8. smurali1

    Taking reference

    While taking datum for finding position, Is it right to do the following in a CMM: 1. Probe three points to form a plane. 2. Probe two circles and join their centres to form a line. 3. Use one of the above same centre as a point to completey fix datum system. (3-2-1 principle). I think the...
  9. smurali1

    Partial nitiriding in part (within part variation)

    Hello all, Thanks for your inputs. Here are some feedback and queries from me: 1. We maintain nitriding temperature at 515 deg. C conctant. 2. Also purging is done during cool off. 3. I tried cupric chloride test on sample pc. It exactly behaves like copper sulphate test, except for the...
  10. smurali1

    Partial nitiriding in part (within part variation)

    Hello mfgenggear, Thanks for your feedback. Here are answers for some of your queries and my follow up questions. 1. Nitriding is by gas nitriding. 2. No white layer removal is done. Grinding done on only very minimal area for bearing fitment. In gear area and most of the areas of the part...
  11. smurali1

    Partial nitiriding in part (within part variation)

    Hello, We are doing nitriding of large internal gear (appx. 1.5m in dia) We are finding that some areas are as bright as original steel material before nitriding. There is high level of variation within a part. We tried 5% copper sulphate solution to check the effectiveness of nitriding...
  12. smurali1

    Casting hardness

    Hello all, Thanks for your comments. Now I have few more questions: 1. Will the hardness on the skin of the casting be more or less than say 1 mm below the skin? 2. Why the hardness checking surface is prepared by grinding before hardness check (for eg. Poldi or Foundrax) I am trying to...
  13. smurali1

    UT inspection (flaw detection) on a 6" round x 18" long Bar.

    Hello, I do not have much experience with UT. But I have heard UT technicians talk about deadzone. i.e. they say UT does not detect any cracks in the first 15 mm from the surface where UT probe is kept. These undetected cracks can show up after machining. Thanks, SPM
  14. smurali1

    Casting hardness

    Hello, We are procuring Grey cast Iron casting (GG25) from one of the supplier. Supplier has checked in 10 spots and certified the casting to 185-200BHN using Poldi hammer. He also has certified UTS value as 305MPa. Supplier then shipped the casting to Europe. When European plant checked...
  15. smurali1

    Soot

    Hello, We are doing carburising hardening some gear parts. After tempering we do shotblasing of the parts. Now, customer is insisting on 100% removal of soot from the parts. He also wants the part to look like steel grey and not blackish. The evaluation method is rubbing a tissue paper on the...
  16. smurali1

    Decarb

    Hello, Here is one clarification: We have to cut the threads before carburising. But we do not want hardened threads to avoid chip off. So, we apply anti-carb paste (Durferrit) to avoid carburising in the thread. Please also note the paste is very thick, almost like dough base of Pizza. But...
  17. smurali1

    Decarb

    Sorry for the confusion. I meant 50 meters. As redpicker rightly pointed out the transport time is less than 2 minutes.
  18. smurali1

    Decarb

    Here are some information: 1. We use Anticarb which is very thick in consistency. (almost like a dough used for pizza) 2. The time between anticarb application and start of HT is appx. 1 hour. 3. Hardness at the area where anti-carb is applied is 57 HRC and carburised depth is appx. 70~80 mic...
  19. smurali1

    IGO

    Dear all, Thanks for the response. We do measurement as per Dbooker630. i.e. 500x un etched condition. However, the issue came up when HT shop did not concur with lab's finding. HT shop was not accepting that reporting of max. length is the right method. So, I wanted to check on standard's...
  20. smurali1

    Decarb

    We are doing carburising (long cycle - case depth of appx. 3mm) in pit type gas carburising furnace (endo gas). The part is taken out and quenched in seperate quenching tank which is appx. 50 mts away. 1. What should be done to control decarb on the surface? We also apply anticarb paste in...

Part and Inventory Search

Back
Top