Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: mycon73
  • Order by date
  1. mycon73

    Defining Helix Law Curve(s)

    Hi, I finally got my Helix profile the way I want it - along the tappered face. For the most part, my cutting or groove tool sweeps well, until it gets near the end. How do I prevent the cutting tool from angling or thickening as it sweeps around the Helix? Thanks.... Jason Misztal Fuel...
  2. mycon73

    Defining Spiral with Law Curves

    Hi, Since, I am blocked from various image sites, I will try to spell out my delima. I have defined 2 points. One point has a radius of: 4.828, which is my starting point. The other point has a radius of: 5.084 If a line is drawn connecting the 2 points, this will represent my...
  3. mycon73

    Defining Helix Law Curve(s)

    Hi, Since, I am blocked from various image sites, I will try to spell out my delima. I have defined 2 points. One point has a radius of: 4.828, which is my starting point. The other point has a radius of: 5.084 If a line is drawn connecting the 2 points, this will represent my...
  4. mycon73

    Defining Helix Law Curve(s)

    Hi, Received a lot of good suggestions, but for some reason, I still cannot get the Helix profile in a desirable location or get a clean sweep out of it. I projected the curves as suggested, but when I go to create the Helix Law Curve, I'm not sure which one to pic for my needs. So far...
  5. mycon73

    Defining Helix Law Curve(s)

    Hi, This partially in reference with my, "Create Spiral Groove" topic. I need to create a spiral pattern to use as my sweep guide & the Helix curve feature seems to be the best feature to use. I have start & stop points, ID & the # of turns required that will define my groove pattern...
  6. mycon73

    BOM IN NX CAST 4

    Hi, Here's some NX 3 CAST: C:\UGS\NX 3.0\UGDOC\html_files\assemblies\func_details\analy_diagram.html (I think it's the same link for your PC). Perhaps, it's the same for NX 4. Jason Misztal Fuel and Utility Systems UG Designer Goodrich Corp. Rome, NY www.goodrichrome.com
  7. mycon73

    Define Models

    Hi 4Mranch1 & plmexchange, Thanks for the feedback. Seems both of these could work. I think I want to use the UDF, but I forgot where to go to create it. Where do I go to create a UDF? I found the Define Deformable feature & will figure out on how to use this to see if this is...
  8. mycon73

    Error

    Hi, Is the component you linked the bodies still in the model structure? It appears that it has been removed out of the model structure & therefore, your linked body does not know what to link to. Hope this helps. Jason Misztal Fuel and Utility Systems UG Designer Goodrich Corp. Rome...
  9. mycon73

    Define Models

    Hi, I would like to create a model that works similar to a model with a Part Family Table in it when adding it into an assembly. However, I want to be able to enter some variable dimensions, such as ID, OD or Hole Dimension Angle for a part & based off of these entries, the rest of the model...
  10. mycon73

    Create Spiral Groove

    Hi Hudson or Whoever Else That Can Help, I am trying to make an internal groove that will be square shaped along a tappered face. I have 2 defined points in which I need to start & stop at & the groove cut will have a .25 depth with a .25 width. Perhaps, the cable feature will work better...
  11. mycon73

    Create Spiral Groove

    Hi, It's been a while since I've done this. I need to make a spiral groove onto a tappered bore. I attempted to use the Helix feature to create my spiral pattern, but when I sweep it, my groove is not going along the tappered face. How can I make the spiral pattern that goes along the...
  12. mycon73

    Interpart Expressions of Part Families?

    Hi, I created a component & created a part family table in it. This component design intent is to drive an upper level component, in which a few more features will be added onto it. Is it possible to have inter-part expressions or links between part family tables that are in two different...
  13. mycon73

    Part Family Contstraints

    Hi Phippd, I am not familiar with deformable part. Where can I find more info. on this? Does this requireq a "special" licience? Thanks Jason Misztal Fuel and Utility Systems UG Designer Goodrich Corp. Rome, NY
  14. mycon73

    Need hpgl data pulled into UG NX3 drafting

    Hi, Does Mentor DX Designer '.hpgl' have the capabilities to open in Adobe software products? Adobe Illistrator seems to work well for convering different CAD systems to another CAD system. Illistrator, in particular has 2 dozen or so convertiable or usable files that it can accept. Hope...
  15. mycon73

    Part Family Contstraints

    Hi, I'm creating some standard models & part families seems to work well for pre-defined dimensions. Is it possible to have user enter values for specified dimensions or constraints, rather than going through a list of pre-defined criteria, then selecting desired component? Also, is it...
  16. mycon73

    Old & New UG File Naming

    HI, Just curious... If a company uses the Component ID as its drawing UG file name & now wants to create parametric models for them. In the history, the company only had drawing files which is used in multiple systems. Now, that they want to create models, the company is trying to...
  17. mycon73

    Standarizing a Model?

    Hi, I want to create a "Standard Model", which will basically look the same, but the size will vary. I think I want to use Part Families, but I have forgotten how it fully works or is created. Perhaps, I want to use something else. Basicaly, I have a bunch of cylindrical ranging from 5"...
  18. mycon73

    Grip Programs

    Hi, Where can I find some self-help or training material on grip programs. I would like to create a grip program to link the title block with Teamcenter & it's been quite a while since I've done this. Also, where can I find some info. on creating part families. Thanks Jason Misztal...
  19. mycon73

    Creating a "Solid" Appearing Line

    Hi, We create our designs or images using Unigraphics, Pro-E or Medusa & need to keep our images in one of these CAD files. On the CAD side, we need to control the length, width hight of a line only need a "solid" appearing line. In most cases, having hatch markings suffices for us. As...
  20. mycon73

    Creating a "Solid" Appearing Line

    Hi, Our vendor uses Adobe Illistrator & I am told that Illistrator accepts AutoCAD 2000 '.dxf' files fairly well - with distorting or blowing up the imported image. We don't have AutoCAD 2000 & our files are converted to '.dxf' from Unigraphics, Pro-E or Medusa. When we create a "solid"...

Part and Inventory Search

Back
Top