Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Mitesh87

    Centrifugal Pump Shaft

    Thank you for your valuable reply.
  2. Mitesh87

    Centrifugal Pump Shaft

    Hello, I want to know that does Centrifugal Pump specially Overhang type, shaft come in contact with Process fluid? If yes than in which area?
  3. Mitesh87

    Sundyne Vs Multistage Pump.

    Hello, I want to make (General) presentation on Sundyne vs Multistage pumps. Can you please provide any content or article so that i can add up in my presentation? Thanks in advance.
  4. Mitesh87

    Multistage Pumps VS Sundyne Pump

    JJPellin Thank you for your valuable reply. Can you please provide me the details or reasons why you want to go for multistage pump over sundyne pump? To all experts - I want to know which is good selection sundyne or multistage pump? Thanks and Regards.
  5. Mitesh87

    Multistage Pumps VS Sundyne Pump

    Thanks for your valuable reply. JJPellin : Sir i already search "Sundyne" in this forum but i did not get specific difference between sundyne vs multistage pump. Once again I am clarify my query. I just want to know which is the better option multistage or sundyne. Kindly provide your views...
  6. Mitesh87

    Multistage Pumps VS Sundyne Pump

    Thanks for the reply Artisi. May i know which information you required? Lets talk specific - Process parameters are as under. Process fluid- light nephtha Max temp - 150 C , Min temp - 52C Viscosity - 0.56cP flow - 27.1 me/hr Head - 312.8 NPSHa - 16.96 Hy kW- 15.06 In the above case i have 4...
  7. Mitesh87

    Multistage Pumps VS Sundyne Pump

    Respected Sir, I have a question regarding comparison between Multistage Pumps vs Sundyne Pump. I am asking generally not for specific parameters. So Kindly provide your views on why Sundyne is good over multistage or vise versa. and comparison between these two. If you have any...
  8. Mitesh87

    seal face material selection.

    Pumps are - Heater Recycle pumps & Fluid name is - Hydrocarbon. Pumping temp is 360 (Normal) & 425 (Max) Vapor pressure is - 0.04 kg/cm2a Specific Gravity is - 0.831 @ 360C Viscosity - 1.03 cP @ 360C. Yes vapor pressure is correct.
  9. Mitesh87

    seal face material selection.

    Pumps are - Heater Recycle pumps & Fluid name is - Hydrocarbon. Pumping temp is 360 (Normal) & 425 (Max) Vapor pressure is - 0.04 Specific Gravity is - 0.831.
  10. Mitesh87

    seal face material selection.

    Thank you sir for your reply. Agreed. For high temp we can not use elastomers. we go for metal bellows. but sir what about seal faces? Which material should we go for seal faces? Thanks in advance.
  11. Mitesh87

    seal face material selection.

    Dears, I have a query regarding seal face material. As per api 682 3rd edition , there a table B.2 which shows maximum temperature limit of faces. so as per table 425 degree is maximum limit. If my pump fluid temperature is around 600 or 700 degree in that case what will be my face material...
  12. Mitesh87

    Selection of seal plan

    Hello Chpal1984, Thank you for your reply. Sorry but I can not understand much with this. What i understand is if my process fluid temp is very high and if i go with plan 21 & 53B means FB than i get extend seal life. As per my knowledge if my temp is very high i can not cool because if i use...
  13. Mitesh87

    Selection of seal plan

    Hello, While selection of seal, if my process fluid is toxic and i want that fluid shall not come out to atmosphere. so whether i should go for 3CW-FB or 3CW-BB ? Normally i have seen 3CW-FB because in this case in board sealing by primary plan 11 or 21 and out-board sealing by 53B. and if i...
  14. Mitesh87

    Select mechanical seals

    In addition to the main Question, I am also confuse that When I go to category 2 and 3, Because both are for API pumps. so which category i choose while selection of seal?? Thanks in advance.
  15. Mitesh87

    Seal selection.

    As per API 682 , In seal Types A,B,C. Type B flexible element normally rotates.and in Type C flexible element is normally stationary. As I understand - if seal seal-face surface speed is below 23 m/s than flexible element rotates and if seal- face surface speed is more than 23 m/s than...
  16. Mitesh87

    seal plan change

    Thank you sir...
  17. Mitesh87

    seal plan change

    Sir, Thank you very much for your reply... yes we can replace it with air cooler. Sir, but i have 1 query regarding with solution. here my temp. is 50 degree. and if i try to cool by air then my air temp will be near around 38 or 40 degree. (Atm.) So is this temp. is sufficient to cool 50...
  18. Mitesh87

    seal plan change

    Hi all, I am facing 1 issue regarding seal plan change. My issue is - I have 1 pump having service slop oil ( properties are below) in that pump I have only 53a seal plan. Water is used In this plan. Now I have to shift that pump At new location having new service - LSD liquid (properties are...
  19. Mitesh87

    maximum differential pressure

    Thank you GPRnD, As u stated that , The MAWP per API 610 = max suc pr. + 1.1 x max differential pres. i refered API 10th and 11th editions , it shows - MAWP shall be at least the maximum discharge pressure plus 10% of the maximum differential pressure. So, if my max differential pressure...
  20. Mitesh87

    maximum differential pressure

    LittleInch, Thank you very much for valuable reply. I will keep in mind your instructions while asking for the same. As I mentioned that I am New here and all.. But its ok... Hope to see you again for more queries. BR, Mitesh.

Part and Inventory Search

Back
Top