Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. shubbad

    Abaqus modelling

    I'm modelling the wind turbine foundation but in material properties I'm using only modulus of elasticity and Poisson ratio of concrete. As it is an elastic model, the calculation results is overly optimistic? Do I need to consider the plastic properties or If I'm going with the elastic...
  2. shubbad

    Abaqus-Partition

    This is a gravity-based wind turbine foundation where I have modeled the raft portion as a shell. Instead of modeling the soil directly, I represent it using springs and assign spring stiffness values to the nodes (connecting points to the ground using the 'standard' option). In the...
  3. shubbad

    Abaqus-Partition

    In my model, everything is the same in both cases—geometry, material properties, loads, and boundary conditions. The only difference is that in the first case, I did not partition the face, while in the second case, I did. Due to the partition, the node numbers vary slightly, leading to a...
  4. shubbad

    Abaqus-CAE : Radial Partition

    Hello sir, sorry for the confusion earlier. Let me explain the situation. The concreting was completed up to the shaded region, but due to the rain, a 200 mm layer of concrete was washed away. In my analysis, I want to partition this 200 mm layer so I can assign it a different property...
  5. shubbad

    Abaqus-CAE : Radial Partition

    Hello Sir. I have highlighted the relevant area in pink on the 3D model. I need to create a 200 mm partition so that I can assign two different properties to the sections. Thanks & Regards, Shub
  6. shubbad

    Abaqus-CAE : Radial Partition

    Hello everyone, I need some help. I need to create a partition on a surface, similar to what I've shown in the front view. However, I am struggling to partition it in 3D. Should I sketch the section and revolve it to ensure the entire radial surface is divided into 200 mm segments? I've attached...
  7. shubbad

    Abaqus: Composite layup

    I will make it more clear through Images. I have made part like this but when I am sketching like this these will not act as single component. If I want to calculate the forces or moment at the bottom , it will give different values for both, but if i can make it as a single component then if...
  8. shubbad

    Abaqus: Composite layup

    I want to create a 3D shell part.I am modelling two shell part as a single part, both the shell part has different thickness and different material property. I tried composite Layup, but I'm unable to do. I'm attaching the image how the geometry will be. Please guide. Regards, Shub
  9. shubbad

    Abaqus-CAE, Sweep cut problem

    I am attempting to cut the portion as indicated in the image. I am using a sweep cut, but I'm not achieving the desired result. Although I can cut it, the final position is not as intended. Note: The first two points are collinear, but the third point is not. I have also attempted solid...
  10. shubbad

    Abaqus-CAE, Shell element

    I modeled a slab in Abaqus using Shell elements, and I require the S33 value. However, for shell elements, S33 is zero. What alternative approach should I consider? Your guidance is appreciated. Thanks and Regards.
  11. shubbad

    Abaqus-CAE : Facing problem in Assembly

    I attempted to use the 'rotate instance' function, but it isn't aligning perfectly with the desired position. The 3rd point is not coming to the third datum point, first two point of the instance came to the datum point as shown in figure. Please guide Thank you
  12. shubbad

    Abaqus-CAE : Facing problem in Assembly

    I am facing a problem positioning the instance. I am trying to rotate the instance the way I need, but I am unable to do so. I have marked the point, and I have drawn how to position it. Please guide me.
  13. shubbad

    Abaqus-CAE : How to put the instance in Assembly at correct position

    I will explain my question. I have modeled it, but I am unable to understand the position of the steel cable from the figure. There are 40 steel cables, and I know I can place them in a radial pattern. However, I want to know how to determine the specific position for each steel cable and how to...
  14. shubbad

    Abaqus-CAE : How to put the instance in Assembly at correct position

    This is the cross-sectional view of my model, and there is one steel member. However, during modeling, I am unable to understand the position of the steel member, so I cannot place it in its correct position. The total number of steel members is , but from the cross-section, I am unable to...
  15. shubbad

    Abaqus-CAE : Circular footing soil as Spring

    Thank you so much for your guidance, sir. It has helped me a lot. I have a few more doubts. I have partitioned the circular area into different circular regions so that I can assign different stiffness values, but for that, I have to select the nodes for each circular region. Can you guide me on...
  16. shubbad

    Abaqus-CAE : Circular footing soil as Spring

    Sir, For me it is coming like this
  17. shubbad

    Abaqus-CAE : Circular footing soil as Spring

    Will you please explain it little more?
  18. shubbad

    Abaqus-CAE : Circular footing soil as Spring

    I tried but failed. I tried different partition method but still not getting the things. It worked only for the upper portion.
  19. shubbad

    Abaqus-CAE : Circular footing soil as Spring

    Yes, I have partitioned the surface into different layers so that I can assign a different stiffness value to each layer. However, I am now facing an issue with meshing. I need to assign mesh control as 'Hex-Sweep through medial axis.' I attempted to partition for meshing, but the orange color...
  20. shubbad

    Abaqus-CAE : Circular footing soil as Spring

    The suggestion you gave,I did that and it worked. I have applied the spring in other two direction by putting the stiffness value 10% of the 3rd direction and it worked. Thank you so much

Part and Inventory Search

Back
Top