Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: monam
  • Order by date
  1. monam

    i AM LOOKING FOR A CRD FOR GAS TUR

    i AM LOOKING FOR A CRD FOR GAS TURBINE ,ITS CONTROL SYSTEM IS LARRY SYSTEM .CARD SPECIFICATIONS dual channel card (E122-205-028 Series) drive electro hydraulic servovalve; manufacturer MOOG. And power supply (E128-205)...
  2. monam

    MTU diesel Engine

    application standby power gen.
  3. monam

    GE Gas Turbine Frame 5

    Dear Engineers. I would like to know what are the parts ( Mech,Elec and instruments ) to be replaced in the major overhaul of GE Frame 5, 25MVA,18.5MW.?
  4. monam

    MTU diesel Engine

    Dear Engineers. I came to know that MTU engine type 12V396 (950KVA-912KW) is discontinued, is that true and if there is any notifications? what is the best MTU alternative engine?
  5. monam

    What is the best PLC you recommend

    now OEM control system is mark 6E which is very expensive, therefore I heard many PLCs has same reliability features and less expansive . if somebody has any recommendation.
  6. monam

    What is best solvent ( environmenta

    thanks all my generator is 26 MW Brush type , due to some reason sealing failed and lot of oil entered the generator housing and due to heat oil spread over all winding , walls and ceiling , everywhere inside housing. I want to pull out rotor from stator and do thorough cleaning . who has such...
  7. monam

    What is the best PLC you recommend

    what is the best PLC you recommend for Gas Turbine frame 5 for upgrading old control system speedtronic Mark II?
  8. monam

    What is best solvent ( environmenta

    What is best solvent ( environmentally safe) can be used for big generator (stater & rotor) contaminated by oil? what is the standard amount required per area?
  9. monam

    MTU 18V2000 troubleshooting

    yes, you are right .the AGC flags an underspeed alarm.you explination meets my conclusion , mtu provided new mdec without SAM, this will not all complete sequence of startup and operation. by this conclusion is It possible to mtu to cancel/override this from the memory if I send to them or we...
  10. monam

    MTU 18V2000 troubleshooting

    Engineer Mikel, many thanks for your comments, your description to condition is perfect, I am not sure if mtu cfigration for mdec memory will solve the problem by cancelling CAN alarm or not? I don know how to get help from FreddyNerk or contact him?
  11. monam

    MTU 18V2000 troubleshooting

    another , how to get mdec software to do congiration ?
  12. monam

    MTU 18V2000 troubleshooting

    thanks again The mdec was damaged , the question is ? does the CAN1 alarm preventing the speed to raise or the governor to take the lead? synchronize will be if load sharing online in later stage. do you thing its independent issue? I mean reach the speed of 1500 RPM and CAN1 alarm
  13. monam

    MTU 18V2000 troubleshooting

    thanks again AGC was not replaced. this generator is emergency standby, SUPPLY POWER if main source of power CUTOFF, it can be shared as well. I found no CAN in AGC connected , AS BOTH are isolated and FROM MDEC upto junction box. in another way CAN1 nodes are EFG, CAN2 BCD nodes are ends...
  14. monam

    MTU 18V2000 troubleshooting

    Do you think if I connected CAN1&CAN2 wires which are free now to the AGC ( DEIF type) to allow MDEC to receive feed back signal will clear the alarm? best Regards AM
  15. monam

    MTU 18V2000 troubleshooting

    Thanks dear Mikel the picture for the alarm on MDEC IS attached and starts appearing after installing new MDEC, it could be eliminated with old MDEC!! Is this alarm preventing reaching nominal speed? The problem this alarm as per manual caused by CAN1 BUS nodes are not connected. I checked...
  16. monam

    MTU 18V2000 troubleshooting

    hi all after thorough checks for all CAN1 CAN2 wiring are in open circuit as the engine was running normal , it 180 AND 187seems AND to me the wiring was not as per the standard an this alarms were canceled on MDEC ? ANY BODY HAS ANY IDEA HOW TO CANCEL ALARMS ERRORS 180 AND 187? or any other...
  17. monam

    MTU 18V2000 troubleshooting

    the new mdec is correctly configured by the supplier, thanks to all for your help , I will feedback
  18. monam

    MTU 18V2000 troubleshooting

    We have MTU engine 18v2000. its MDEC damaged and replaced by new one. The new one starts the engine, but the speed does not go more 1400rpm, and HZ is 47 only not 50 HZ. the alarm code appeared on ECU is 180 and 187 which mean problem on connection on CAN 1. We checked mechanically and found...
  19. monam

    SFC

    thread238-41946 Thanks for all knowlege provided by the group. I would like to know what the checks done during Major inspections for SFC/ LCI installed in GE F9

Part and Inventory Search

Back
Top