Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Kasmat2013

    Abaqus AM

    Dear FEA way, Greetings, I was trying to simulate the progressive buildup of a simple rectangular bar using the AM module of Abaqus 2022 and I got the following error message when I tried to submit the job: "the region selected for the following element progressive activations contains invalid...
  2. Kasmat2013

    Abaqus AM

    Dear FEA way, Thank you for your reply. I will try and get back to you. I used Excel to generate the event series.
  3. Kasmat2013

    Abaqus AM

    Dear FEA Way, Thank you for your reply. Yes, I have visualized the plot of the toolpath, but it doesn't have information about the heat source. Here I have attached the .inp file, but I couldn't attach the whole file because the file size is a bit bigger than 200MB. Should I send it to you by...
  4. Kasmat2013

    Abaqus AM

    Dear FEA way Greetings, I am able to simulate the progressive buildup of a cylinder. The width of the material added at a time is 300mm, and I want to apply the heat source uniformly across the layer width, but as you can see in the simulation video attached, the AM modeler only applies the...
  5. Kasmat2013

    Abaqus AM

    Dear FEA way, Greetings, I was running a sequential thermal-structural AM problem and it prompted the following error message. UEPActivationVol: Unknown jPtkEvtType 2 or jPtkAlgo 1 for MaterialPath I couldn't figure out the cause. Would you help me please?
  6. Kasmat2013

    Abaqus AM

    Dear FEA way, I was trying to integrate a DLOAD subroutine with AM model by just adding the DLOAD FORTRAN file into a job for structural analysis but the simulation is just jumping from the beginning to end without simulating the moving load. Is it normally possible to integrate a separate...
  7. Kasmat2013

    Abaqus AM

    Dear FEA way, Thank you very much. I will get back to you.
  8. Kasmat2013

    Abaqus AM

    Dear FEA way, Thank you very much, actually the convective and radiative heat losses are one of the output variables that I am looking for.
  9. Kasmat2013

    Abaqus AM

    Hey FEA way, I generated the event series with excel and it is working for me now. But, I got thins warning messages while the analysis is running. Output variables filmcoef and sinktemp are not supported for output with load label ffs and ffsnu. Output variables filmcoef and sinktemp are...
  10. Kasmat2013

    Abaqus AM

    Thank you very much. Modifying the script has become difficult for me. Is there any other method you are aware of which can be used to generate event series to build a simple cylinder?
  11. Kasmat2013

    Abaqus AM

    Dear FEA way I got all the required script files. I tried with the G-code file available with the files and it works well. As I understood the G code was generated with replicatorG software which is not available by now I think. I generated the G-code for my part using Ultimaker Cura software...
  12. Kasmat2013

    Abaqus AM

    Thank you very much FEA way, I will look for it then. Once I found, I will try it and get back to you if I face difficulties.
  13. Kasmat2013

    Abaqus AM

    Thank you very much FEA way. I am not good enough in python programming, Would you mind if you help me in writing a program that can generate event series.inp file from a G-code, please? We may also set some form of academic collaboration so that we can publish the research output together. What...
  14. Kasmat2013

    Abaqus AM

    Hello, I was trying to simulate the progressive element activation in a cylinder. Would anyone suggest to me how to generate an event series for the addition of material in cylindrical coordinate?

Part and Inventory Search

Back
Top