Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: E2005
  • Order by date
  1. E2005

    scaling and offsetting analog output

    VE1BLL and ScottyUK 'm' and 'b' are depedent on maximum supply voltage. My supply is chosen by user it can be between 5-20V. The only thing that does not change is the sensor output which is 0.5V to 4.5V. That needs to be mapped to 0.5V=25% of suppy and 4.5V=75% of supply. If supply was fixed...
  2. E2005

    scaling and offsetting analog output

    ScottyUK , When i map 0.5 to 4.5V input range to current required output range which is 0-8V i get a transfer function Vo=sVin + b where Vo= desired output, Vin is the sensor signal (0.5 to 4.5V) and s and b are the span and offset. For s= 2 and b=-1. I get the desired output. If there was an...
  3. E2005

    scaling and offsetting analog output

    I cannot use an Arduino Uno, just looking for an analog way to scale the sensor signal which varies from 0.5V to 4.5V to 25% of supply to 75% of supply respectively. The supply can be chosen between 5V to 20V DC
  4. E2005

    scaling and offsetting analog output

    This is NOT onesie.
  5. E2005

    scaling and offsetting analog output

    Mike Yes, sorry misunderstood your question. The supply can vary from 5V to 20V DC. The sensor output will always be between 0.5V to 4.5V but the supply can vary from 5V to 20V.
  6. E2005

    scaling and offsetting analog output

    The supply is +8V. I can scale output to this particular supply voltage with opam but the problem is user wants to be independent of the supply voltage. They want to choose a desired supply voltage and the out put sinal (0.5v to 4.5V) needs to scale to it in the following way - 25% of...
  7. E2005

    scaling and offsetting analog output

    I have a 2.5V DC output signal ( its range is 0.5V to 4.5V), it needs to be scaled from 25% of supply to 75% of supply voltage. The supply voltage is a variable.Due to constraints i cannot use microprocessors or other fancy signal processing parts, need to stick with basic parts like opamps ...
  8. E2005

    IEC for mechanical devices/products

    I am looking for a satisfatory answer to the question of which IEC standards apply to mechanical devices/systems in general ?? does IEC 60601-1 3rd edition apply to mechanical parts/devices? IEC standards seem most applcable to devices which have any kind of electrical element but say you have...
  9. E2005

    IEC standards application to mechanical systems

    I am looking for a satisfatory answer to the question of which IEC standards apply to mechanical devices/systems in general ?? does IEC 60601-1 3rd edition apply to mechanical parts/devices? IEC standards seem most applcable to devices which have any kind of electrical element but say you have...
  10. E2005

    compliance for medical device

    I am new to compliance. We make two types of devices, one uses a stepper motor with chopper drive and operates on a 16V, 1500mA rechargeable battery. Its insulated from body. There is not wirelss. The other one is similar to a massage vibrator with wireless control, the vibratory is insulated...
  11. E2005

    Question on analog sensor signal processing

    Apologies in my example. 1 kg should produce 5V output, but you get any where from 4.5 to 5.5. This is just for example, in my case its not a 1V variation, it varies. Also if I run a test when the sensor is new, make a loop up chart for future and later if the sensor starts drifting (offseting...
  12. E2005

    Question on analog sensor signal processing

    Thanks to all your inputs. Its an pleasure to be here. Firstly I was talking about the drift over time in the sensor not the circuit.Kalman filtering does seem like the best solution but hoping for an easier solution.By repetability I meant for the same input you dont get the exact output. Such...
  13. E2005

    Question on analog sensor signal processing

    Not sure if its a basic question to ask. If you have an analog sensor and the output drifts over time or output is non repeatable(input being constant). Also assume thats the best sensor you can get and you are relying on those values to set thresholds etc. Is there a way to take care of...
  14. E2005

    Power supply rejection ratio LM386

    Hi, I had read that power supply rejection ratio(PSRR or PSR) follows open-loop gain curve(or CMRR curve) meaning it drops off with frequency. I saw that in many opam datasheets like OP1177 etc but when looking at LM386 data sheet(page 4, PSR Vs frequency curve) it shows reverse trend , meaning...
  15. E2005

    Transient suppressor

    can anyone tell the basic difference between using an off the shelf transient suppressor chip ( such as Texas Instruments SN75240) and making ones own RC filter circuit.Apart from performance differences(cut off etc) are there other differences and which is better.
  16. E2005

    Cadence allegro, orcad or altium , which one to get?

    macgyvers2000 : Thanks for your insight. It was very useful. Do you know how altium fares in the market( number of users point of view) as compared to cadence. I understand both cadence and altium have their pros and cons. I used multisim/ultiboard before but when i was interviewing for jobs...
  17. E2005

    Cadence allegro, orcad or altium , which one to get?

    IRstuff: Usually i do not need to swap files. But mecahnical guys ask me at times for a step or iges files so they can put cad model of circuit in the package. So something which can do CAD model of circuit along with other ( schematic capture and layout ) would be helpful.Thanks minimelfer: i...
  18. E2005

    Cadence allegro, orcad or altium , which one to get?

    I have been using eagle for schematic capture and layout so far. I need to get a better one. Can anyone suggest which one to get. I need to do schematic capture ( hopefully able to simulate too) and pcb layout. I have tried multisim/ultiboard also in the past. Is there one which is industry...
  19. E2005

    How to control stepper motor efficiently

    Hi Mike, Thanks. I don't have book by C.K.Taft. AI Leehouts name came up in patents. Not sure if you suggested at looking at that. Will continue to look for free info online specifically on acceleration/deacceleration profiles and how to vary pulse divider,ramp divider and stepping ( on the...
  20. E2005

    How to control stepper motor efficiently

    I am using hayden can stack motor z20000 series, with a r controller from Trinamic. The software provides different control options like setting max velocity, acceleration, ramp divisor , pulse divider , micro stepping etc. Is there a resource somewhere on how to best optimize these parameters...

Part and Inventory Search

Back
Top