Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JAE on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Raddy13

    Tolerance Stack-up with O-ring Fit

    If you are doing a stack-up to determine how far off-center a plug inserted into a hole can be, how do you handle it if the plug has O-rings? I have dimensional tolerances on the O-rings, but if the ID is shifted 1mm to the right relative to the OD, will the plug then be 1mm off-center as well...
  2. Raddy13

    When is it better to use coordinate tolerances to locate a hole instead of true position?

    Make sense. Thank you for the replies!
  3. Raddy13

    When is it better to use coordinate tolerances to locate a hole instead of true position?

    I'm learning about GD&T out of a textbook somebody had at work and there are questions at the end of each chapter that I assume are meant to be discussions with the instructor. In the first chapter on position tolerance, one of the questions is, "When is it better to use coordinate tolerances to...
  4. Raddy13

    10% rule for runout inspection fixture

    Actually, now that I'm thinking about it, shouldn't the spindle runout just be below the measurement error of the dial indicator?
  5. Raddy13

    10% rule for runout inspection fixture

    Ah good point, thank you. Is there a guideline for how much runout tolerance I should require for the spindle based on our callout?
  6. Raddy13

    10% rule for runout inspection fixture

    I'm working on an inspection fixture for a shaft that has a 0.02 Runout called out on the drawing. I'm not experienced in designing inspection gages and fixtures, so I've been reading up on it and I came across the 10% rule, that inspection gage tolerance should be about 10% of the tolerance it...
  7. Raddy13

    Perpendicularity on multiple holes along single axis

    Thank you for the replies. I just went ahead and added frames to each dimension. Appreciate the help!
  8. Raddy13

    Perpendicularity on multiple holes along single axis

    I'm working on a machining drawing and one of the features is a hole with multiple diameters (from 15, 18, 20, and 22mm) all along the same axis. Do I have to set a perpendicularity control frame for each dimension or can I set it for the top most dimension and have it apply to entire axis for...
  9. Raddy13

    Edit Routing Path/Objects

    I'm working on a hose routing project and since we're early in the design, the endpoints of the hoses and tubes are changing locations frequently. I've been using the Mechanical Routing application by setting up my datum points, creating a linear path through the points, and then assigning...
  10. Raddy13

    Collapse repeat components in Assembly Navigator

    Perfect! Thank you.
  11. Raddy13

    Collapse repeat components in Assembly Navigator

    I'm currently comparing my assembly model to our real-world BOM, and I wanted to know if there was a way to collapse repeat components together within an assembly (for example, multiple instances of the same bolt), so that I can quickly verify the quantity of each item. Currently, they all show...
  12. Raddy13

    Bridge Curve Disappears on Update

    We recently upgraded to NX-9, and I've found that if I update something that breaks a bridge curve, when I fix the bridge curve, it disappears. Any later features that use the curve remain broken because I can't select the curve to fix it. When I right click on the feature it doesn't even give...
  13. Raddy13

    Deselect all of intent setting

    Ah, awesome, thank you for the help and sorry for not searching the forums more thoroughly. Thanks!
  14. Raddy13

    Deselect all of intent setting

    We just upgraded to NX-9 and I've noticed I'm no longer able to deselect "all of intent" any longer. For example, when I'm doing edge blends with the "tangent curves" setting, if I select a chain of edges that it's unable to blend, when I press Shift to deselect them, it only deselects the one...
  15. Raddy13

    Make certain components dimly visible in assembly

    Sorry, NX8. Is see-thru emphasis in the object display dialog?
  16. Raddy13

    Make certain components dimly visible in assembly

    I'm making exploded views and taking screenshots of a large assembly for an assembly manual we're making. I want the sub-assembly view I'm working with to be easily visible, but I'd also like the rest of the components dimly visible so that shop guys have a frame of reference when putting it...
  17. Raddy13

    Making two swept solids surface tangent to each other

    I managed to get it to work by using Through Curves Mesh on smaller pieces of the cross-sections and then sewing them all together. Thanks for the help!
  18. Raddy13

    Making two swept solids surface tangent to each other

    Whoops, did not realize that. Here's the attached file. I tried using Through Curve Mesh, but it's only drawing one half of the rectangular shell, and I can't get it to draw the other half. Unfortunately, my license doesn't include Studio...
  19. Raddy13

    Making two swept solids surface tangent to each other

    I'm working on a manifold that I currently have set up as so: Four individual runners (swept solids) Unite four runners Swept transition section between a sketch and the face formed by the four united runners So the issue I'm having is that where the solids meet, the faces are only tangent at...
  20. Raddy13

    Prevent associativity with wave-linked bodies/faces

    I'm designing a new component (NX-8) for an assembly, and because of the size and complexity of the assembly, it's not really feasible for me to do my modeling work with the assembly as the displayed part. The simpler solution would be to WAVE-link the necessary bodies and faces in, but the...

Part and Inventory Search

Back
Top