As Sjones said, it depends upon what spec you are trying to meet. If it is ASME, Section V is the rule. If not, order ASTM Volume 03.03 containing all of the standards applicable to NDT and PT. There are about eight of them for PT.
Bill]
William E. Blum
Manager
NDT Consulting Group Inc...
In the nuclear industry, procedures for stainless steel piping go down to about 0.237" and we don't count any bounces. If we don't have two sided access we get no credit for anything on the other side of the weld because we can't be sure the wave is even getting through the weld. Typically all...
My purpose is to find typical drawings that can be used in ultrasonic thickness testing reports (I suppose hull outlines and sections since that is where much of the testing is done) and in training programs to train personnel on ship construction.
William E. Blum
Manager
NDT Consulting Group...
Does anyone know of any CAD programs that come with typical/sample ship drawings already in them?
William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
The UT sound wave enters the part at an angle, 45 degrees for example, and travels from the OD surface to the ID surface. The path it takes is called the first "leg". Following the law of reflection, the sound bounces off of the bottom at a 45 degree angle headed back toward the OD. This is...
Does anyone know of a standard or spec which describes this process? We are looking for grinding burns.
Thanks,
Bill
William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
Does anyone know of a standard or spec which describes this process? We are looking for grinding burns.
Thanks,
Bill
William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
Can anyone with experience on VLCCs answer these questions?
1. Can you share some experience of climbing in these tanks eg, fixing points etc.?
2. Does the vessel supply an inflatable raft in the event of tank flooding (doing readings from the raft)?
William E. Blum
Manager
NDT...
Contact CSM Materialteknik (www.csm.se) in Sweden.
William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
You might try leak testing if you just trying to determine if they are leaking by or not. The equipment is cheap enough and simple to use. See these sites
http://www.amgas.com/sonpage.htm
http://www.leakzone.com/fa/industrial.htm
Bill
William E. Blum
Manager
NDT Consulting Group Inc...
If no sound hits the defect, no sound is reflected back therefore no detection. The angle of inclination varies with the probe design so you need to contact the manufacturer of your transducer to get the specifics. To learn more about transducer and UT in general visit this site...
You should probably check with your probe manufacturer. However, generally speaking, the crystals in TR probes are set in at an angle thereby "focusing" the beam at a certain depth and reducing the amount of beam spread. Normal probes with one crystal have more beam spread at a given...
You might check with All American Inspections in San Antonio (http://www.aaindt.com/). William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
ASTM 165 will explain penetrant inspection well enough to allow you to perform the inspection you are doing. I will suggest an additional technique typically used in these cases: if possible, apply the penetrant on one side and look for bleed out on the other. Bleed out indicates areas that...
Try www.ndt-ed.org.
Bill William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
Here are a couple of sites that might be of interest to you.
http://www.navy-ndi.com/
http://www.csm.se
William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
If you haven't found your answer yet, you might look at ANSI/AWS A2.4, Standard Symbols for Welding, Brazing, and Nondestructive Testing. You might also post your request at www.asnt.org.
William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441...
Once upon a time we were offering one free NDT procedure to anyone who asked. The offer expired many months ago and we don't have any procedures specifically addressing B-scan. William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail...
Visit www.techstreet.com to purchase and perhaps download. William E. Blum
Manager
NDT Consulting Group Inc.
www.ndt-cgi.com
wblum@ndt-cgi.com
USA 1-877-638-2441
Fax/Voice Mail 1-214-853-5131
Sweden 46-42-14 39 99
One of the best places I have found to purchase standards, many of them downloadable is http://www.techstreet.com/. William E. Blum
Managing Director
Bright Technical Services Inc.
www.brighttechnical.com
wblum@brightechnical.com
USA 1-817-274-1262
Fax/Voice Mail 1-435-417-3992
Sweden 46-42-14 39 99
