INTELLIGENT WORK FORUMS
Contact US
Thanks. We have received your request and will respond promptly.
Log In
Come Join Us!
Are you an
Talk With Other Members
Be Notified Of Responses
Keyword Search
One-Click Access To Your
Automated Signatures
Best Of All, It's Free!
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden.
Students Click Here
Home
Advanced Search You are in the site-wide keyword search. If you'd like to search a particular forum, navigate to that forum and click on the "Search" button in the gray navigation bar.
552 records matched your query of distance between welds . Outputting records 141 to 160.
... or spool piece or minimum distance between 2 welds ? Boilers and just piping in General.
Thanks...
... the "keep the HAZ's from overlapping" rule. Of course at those diameters they use a lot of socket welds ...
....
However, note that if the distance between the edge of the tube and the surface of the mating plate...
... in order to mesh with Shell elements and define RBE2 elements between nodes of both plates.
Another...
... this with me now. This
standard gives minimum distance between two welds on pipe.
Probably this will help...
..." (Not exact title) there is some guidance/requirements on proximity of welds . The minimum distance ...
...I'm looking for "rules" or a least guidelines for the maximum allowable gap between the end of a...
... Attachment Welds No. (3) Socket Welding Flange requires 1.5 mm approximate gap before welding.
ASME B31.3...
...Some design codes define a min distance between welds as a good engineering practice...
... welds , the following rules apply:
When pressure parts extend over pressure retaining welds ...
... have been able to find is cantilever examples. I am needing to test the welds of en eyelet...
... the number of cycles of deflection that would cause the welds to fail. Would this work? There is alot of talk...
... of the HAZ of the two welds would be much more important than the distance between the two welds for RT...
... adjacent welds as far apart as you can and anything less than 100mm tends to run you into trouble...
... that is relatively large for the channel. The end result is that the repad welds and the girth flange welds come...
... is the section of the BPVC that covers how close those two welds can be. I've gone through the 715 pages of Div...
...)/(A1+A2)
2. Iy = I1 + A1 d1^2 + I2 + A2 d2^2
where d1 = distance to center of A1 from y_bar...
...
and d2 = distance to center of A2 from y_bar
This is as simple as I can explain it. Good luck....
...is it pinned at the braces ? is the beam length the distance between the CL intersections (closer...
...) fixed at all welds (ends and diagonals) … more redundant and messy
3) fixed at the diagonals...
...
of the specified minimum yield strength of the pipe,
and the minimum distance between miters measured...
... maximum miter
and distance between miters will not apply. Deflections
caused by misalignment up to 3 deg...
... times the wall thickness of the pipe) as the working minimum distance between welds . With approval I...
...][b]minimum[/b][/i] length of 1D between flange welds , but this is a workmanship limit and not defined...
...For the hot tap on the pipe with a split tee or saddle, the "L" is the axial distance between two...
... between the welds on the header.
Hope it helps....
... the load carried by the welds (?) between the plates
then the RH plate takes these loads and reacts them...
... on the center). So, I have 2 supports with a span of 145 mm, a distance from the load to the supports of 340 mm...
...The pressure vessel code does not specify any minimum distance between weld, simply because...
... considered.
I have Nozzle welded to Shell and Weld edge to weld edge distance for Nozzle from Head...
... between the ages of 22 and 65. That says that about 0.1% or 1 in 1,000 adults are practicing engineers...
... not-so-fine line between inspiring interest in science and technology by demonstrating how unbelievably...
...Demented, I think As-built the beam spans between E and H which is supposed to be a 23 foot span...
... into the slab between E and H, or just from the E to H lines. Unless I'm an idiot, I can't figure out why...
... that the load passes through the center of gravity of my bolts and consider the eccentricity only on the welds ...
....
Or do I have to consider the load as passing through my welds and consider the eccentricity in my bolts...
...In my sketch, say the distance between the bolt and the weld is "a", ignore the small e[sub]y[/sub...
...Hello:
I need help determining the required design moment for the bolts and welds in a single...
... total shear flow equal to the VQ/It shear flow that [i]would[/i] have been required between ...
... and minimum bending moment (ie a fairly long distance apart) and averages the weld requirement. I've seen...
SEARCH AGAIN
Resources
Learn methods and guidelines for using stereolithography (SLA) 3D printed molds in the injection molding process to lower costs and lead time. Discover how this hybrid manufacturing process enables on-demand mold fabrication to quickly produce small batches of thermoplastic parts.
Download Now
Examine how the principles of DfAM upend many of the long-standing rules around manufacturability - allowing engineers and designers to place a part’s function at the center of their design considerations.
Download Now
Metal 3D printing has rapidly emerged as a key technology in modern design and manufacturing, so it’s critical educational institutions include it in their curricula to avoid leaving students at a disadvantage as they enter the workforce.
Download Now
This ebook covers tips for creating and managing workflows, security best practices and protection of intellectual property, Cloud vs. on-premise software solutions, CAD file management, compliance, and more.
Download Now
