INTELLIGENT WORK FORUMS
Contact US
Thanks. We have received your request and will respond promptly.
Log In
Come Join Us!
Are you an
Talk With Other Members
Be Notified Of Responses
Keyword Search
One-Click Access To Your
Automated Signatures
Best Of All, It's Free!
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden.
Students Click Here
Home
Advanced Search You are in the site-wide keyword search. If you'd like to search a particular forum, navigate to that forum and click on the "Search" button in the gray navigation bar.
13,237 records matched your query of concrete Engineering . Outputting records 12501 to 12520.
... though, a course on floods should work too since it's the same principles for a river or concrete trough...
...try here:
http://www.asce.org/environmental-and-water-resources-engineering /environmental...
... column inertia, but if the column is not doweled to the floor with bending moment bars the way a concrete ...
... structural engineering theory -- a lot. If I challenge you on something, know that I'm doing so because I...
... on the spacing of your ribs and whether or not you've got enough solid concrete up against the beam webs to call...
... structural engineering theory -- a lot. If I challenge you on something, know that I'm doing so because I...
...? If so, I'm surprised.
I like to debate structural engineering theory -- a lot. If I challenge you...
... it to pencil out at 10 mph even treating the whole wall and panel concrete footing with the pilaster to resist...
...Pour strips: Breaking a concrete pour into sections, separated by strips which are cast later...
... just be very unlucky. In engineering and construction word gets around, especially not so good word....
... for a tank-bottom annular plate and concrete ringwall by T.Y. Wu, G.R. Liu at the Department...
... of Mechanical and Production Engineering , The National University of Singapore, 10 Kent Ridge Crescent...
.... Column heights are closer to 20'.
I like to debate structural engineering theory -- a lot. If I...
... direction). Even if 25% of that is resisted by each end concrete shear wall, that still leaves around 100...
... defined yield mechanism in the lateral system (usually steel or concrete bracing systems). That yield...
... strategy.
I like to debate structural engineering theory -- a lot. If I challenge you on something...
... will be typical reinforced concrete , nothing special there.
Picture attached.
Maine Professional...
... issues a bit.
I like to debate structural engineering theory -- a lot. If I challenge you...
... proximity to another embed. plate? The type of embed. plate is cast into a concrete wall taking mainly...
... engineering theory -- a lot. If I challenge you on something, know that I'm doing so because I respect your...
... deck is considered as a permanent shuttering and only the concrete slab is considered designed to span...
... not well suited to composite construction.
I like to debate structural engineering theory -- a lot...
... to avoid having to go all the way to Level 3 assessment for this dent...
Anyone got a concrete ...
..., the section has little ductility left and we made an engineering judgement that it be repaired despite being...
... for engineering in your area?
Further, with 1m of similar fill over fill with N=5, you are only concerned about...
... settlememt of 4m of fill and the concrete slab should be designed as fully suspended to span between piles...
... to calculate it for strip and spread footings, does the same rule apply to concrete slabs, mats or rafts?
...
... at risk assessment than geotechnical/structural design. Don't let your client dictate your engineering ...
... engineering and 20 hours of CAD per sheet. Of course for a two sheet project, the numbers will be more...
... too bad if you've done similar buried concrete structures.
Maine EIT, Civil/Structural....
...My company is a small structural engineering office. I am currently searching for a structural...
... (buildings, industrial structures, culverts, retaining walls, linear buckling, seismic, steel, concrete , etc...
... land when I was in my early twenties. Since then I have earned a degree in Materials Engineering and I...
.... He used it out in the detached concrete block garage of our suburban home, also in Ontario- again...
...SteelPE,
Previous report was done last year by an engineering firm before we bought the house...
.... Our foundation is a post tension concrete slab in TX, so there shouldn't be any rot. We recently had...
...Firstly, is it a steel structure or concrete structure? the connection could be very different...
... wacky world of engineering .[smile]
www.SlideRuleEra.net [idea]
www.VacuumTubeEra.net [r2d2]...
...1 for me.
If you look up ACI 332, which is the bare bare minimum for residential concrete ...
.... I think, depending on the type of project, this falls under engineering judgment....
SEARCH AGAIN
Resources
Learn methods and guidelines for using stereolithography (SLA) 3D printed molds in the injection molding process to lower costs and lead time. Discover how this hybrid manufacturing process enables on-demand mold fabrication to quickly produce small batches of thermoplastic parts.
Download Now
Examine how the principles of DfAM upend many of the long-standing rules around manufacturability - allowing engineers and designers to place a part’s function at the center of their design considerations.
Download Now
Metal 3D printing has rapidly emerged as a key technology in modern design and manufacturing, so it’s critical educational institutions include it in their curricula to avoid leaving students at a disadvantage as they enter the workforce.
Download Now
This ebook covers tips for creating and managing workflows, security best practices and protection of intellectual property, Cloud vs. on-premise software solutions, CAD file management, compliance, and more.
Download Now
Talk To Other Members
