INTELLIGENT WORK FORUMS
Contact US
Thanks. We have received your request and will respond promptly.
Log In
Come Join Us!
Are you an
Talk With Other Members
Be Notified Of Responses
Keyword Search
One-Click Access To Your
Automated Signatures
Best Of All, It's Free!
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden.
Students Click Here
Home
Advanced Search You are in the site-wide keyword search. If you'd like to search a particular forum, navigate to that forum and click on the "Search" button in the gray navigation bar.
552 records matched your query of distance between welds . Outputting records 181 to 200.
... and strong axis bending stiffness provides so much more stiffness than the welds on each side of the plate...
...Dont forget that moment is shared between the angle and the gusset according to stiffness...
... if you add up all the bolt edge distances you need to maintain. If you want a min. 1.25" edge distance ...
... 1/2" erection gap between joist shoes you're left with min width = 4*1.25" + 0.5" = 5.5"
[quote...
..., the nut cannot be tightened. Now if you are referring to the distance between the bottom of the base plate...
... it. Now, since the plate is on nuts and there is a gap between TOC and bottom of baseplate, you might...
..., L=2.5sqrt(Rt)
(2) flat plates, L=3.5a
where:
L = minimum distance between adjacent...
... Section AD 160.
1. When the code says "integral" does this mean Full Penetration Welds , anything else...
...?
Depending on a whole bunch of things some distance away from the welding site will get hot. It may get hot...
... to not apply powder coat?
It's not exactly clear from your posts what the roles or relationship between your...
... to distance between spider arms) and see if bump test results change as we rotate it. [b] I’ll talk...
... welds
What do you think could be the cause of the sudden appearance of rotor bend?
What additional...
... welds unless it refers to the minimum distance between adjacent openings (see interpretation B31.1-22-7...
... to proximity of two welds .
Long story short, B31.1 is not going to specify a minimum distance for two...
...Dear Experts;
In the picture attached below shows the distance between the CS & nozzle weld toe...
... is very less than the actual required, as thumb rule the distance between the weld toe shall be a minimum...
... the piers in-between the windows. Without windows my wall has an ultimate moment of 3,038 +/- ft-lbs/ft...
....
I am leaning towards designing the masonry above the opening to span between the head of the opening...
... between 4" welds or are the welds @ 12" o.c.?
Blogett's book notes that the 12" is the "distance ...
..." in-between the welds . However, with ISO symbols, they should also be calling out the number of welds as well. ...
...PAN,
The TOFD is the best alternative for the inspection of the welds to RT and conventional UT...
... be improved by reducing the pulse width of the lateral wave signal. The same applies for inspection of welds ...
...From what I remember in BS2633 it mentions 40mm between the toes of the welds . ...
..., depending on the situation. Usually I try to keep it to within 3 inches between the base of the welds ...
... to come from embedding the stringers some distance into the floor slab to provide full rotational...
... distance into the floor slab to provide full rotational restraint (moment capacity).[/quote]
Firstly, I...
... followed.
Also, it would probably be good idea to define the differences between "heat to fit" and heat...
... to fit when they finally meet one another- without providing field welds or doing templating or dummying...
...There is another way to do this, provide say 0.1mm distance between surf.1 and surf.2 and model 3d...
... the welds but want to know whether the current welds are OK or not. How can I do that?
Regards ...
... l is the length of each transverse weld and b is the weld throat and d is distance between ...
...The moment capacity of the welds is the strength of the weld metal multiplied by the section...
...-to-header welds .
I recently observed from a distance (I was only involved in the tube F/A) as a...
... locally PWHT a single or a few repair welds near one another, we would control the temperature along...
... to be in order to provide adequate separation between the two HAZs of the two welds ? I seem to remember 2" being...
... there is a rule of thumb for this but I can't remember it. How far apart do two adjacent pipe welds need...
... requirement in NAVSEA TP27 to use scribe lines to ensure the proper gap between the bottom of the socket...
... once the pipe is tacked in ?
I welded piping socket welds for 15 years and have been inspecting them...
... what is the minimum distance between the flange butt weld
and web butt weld according to awsd...
... can clean up the edges.
Then you fit the two flanges and the web together and do the fillet welds ...
SEARCH AGAIN
Resources
Learn methods and guidelines for using stereolithography (SLA) 3D printed molds in the injection molding process to lower costs and lead time. Discover how this hybrid manufacturing process enables on-demand mold fabrication to quickly produce small batches of thermoplastic parts.
Download Now
Examine how the principles of DfAM upend many of the long-standing rules around manufacturability - allowing engineers and designers to place a part’s function at the center of their design considerations.
Download Now
Metal 3D printing has rapidly emerged as a key technology in modern design and manufacturing, so it’s critical educational institutions include it in their curricula to avoid leaving students at a disadvantage as they enter the workforce.
Download Now
This ebook covers tips for creating and managing workflows, security best practices and protection of intellectual property, Cloud vs. on-premise software solutions, CAD file management, compliance, and more.
Download Now
