Thanks to you both for your opinions. I've passed it on to my family and it sounds like they're looking to retain the rights for now unless they can't find a buyer. Thanks again!
I'm not a petroleum or natural gas guy, so please bear with me as I may be missing a lot of detail.
My parents have a 60-acre farm in western PA (Jefferson Twp, Fayette County) that they are looking to sell. The property does have natural gas on it (Marcellus shale) and they have been...
We had a differential collar that required a 0.5 Ra finish on a face (not the OD). Stock removal was roughly the same amount as you dealt with. Typically, we could hit this finish using a two step process, removing the first 0.2mm with a rougher tool and the remaining stock with a wiper...
The model setup itself is fairly easy, although it's been about 10 years since I last used Arena. Your biggest challenge to start is tracking box arrival/departure rates for all of the points. You need to determine the time distributions of these to see if they fit a standard distribution or...
The use of stainless PM gears is really going to depend on what dimensional tolerances you want combined with your strength requirements. At 5.5 sq inches, you're probably going to need a 550-ton mechanical press or equivalent hydraulic, depending on the # of gear levels. You can coin for...
All depends on who the headhunter is I guess. The man that pulled my resume out of thin air for my current position became a headhunter when he retired. He was my former company's GM. Depending on how big your field is, you may find that there are these "boutique" outfits made up of retired...
I usually vacuum sinter by pulling the unit down to 50 microns. For heating, backfill with N2 and hold the partial pressure around 300 microns. All of your cooling will be done at that partial pressure using forced N2 as the cooling medium.
One observation I'll make is that you need to...
JohnFox,
What is the flatness/parallelism requirement on the thickness? Next, what volume are we talking about? What are the corrosion requirements? And are you willing to budge at all on the radius corners? What about small chamfers with burr traps rather than full radii? I can mold most...
Greg:
Not too sure of the details yet. The way it was explained to me, it doesn't quite make total sense. If a component fails then the component supplier is responsible for warranty replacement cost. So rather than the cost of the component, they would also have to cover replacement cost...
Check a couple of the machine auction sites. American Axle was just liquidating literally buildings of machinery from their Detroit plant. They're not the only ones doing this. The market has a ton of surplus, even in specialized machinery. Same goes for inspection equipment and the like.
Interesting point on the automotive warranty issue Greg. I was told by a tier 1 customer of mine that GM is now going to mandate that warranty costs of sub-components are going to be shouldered by the sub-component supplier (those who agree to that deal I guess). Any truth of this being a...
I'm a Pittsburgh native (don't live there anymore), but most of the advice you've received here is adequate. If you're relationship has progressed this far, shirts and slacks are likely sufficient. You can bring cookies if you like...as mentioned people with allergies will know. Also, don't...
All depends on what you count as "efficiency". If my managers don't consider the time I spend on the floor helping to train operators, fix CMM issues, fix CNC programs, help train setup techs, etc., as billable time towards the bottom line, then I'm not doing so well! If they count that and...
Swagelok will also coat some of their smaller packing bolts in the valve assemblies with a material called Everlube. It's a teflon based coating. Coating is always focused on the threaded areas, I believe to help with the prevalence of galling in 316ss.
How accurately can the new EDS systems gage Boron content? Meaning, does the boron content have to be of a certain % of the total material to adequately pick it up? Or are trace amounts (say in the .025% range) able to be detected?
Sorry for the hijack. We've just never been able to get a...
