Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Thanh Tran

  1. Thanh Tran

    Edge finding function on Mitsubishi

    @laserkatana Today I tried to test the edge finding function. I inserted these lines before the line M66 #10202=0.2 #10203=0.8 #10204=0.2 #10205=0.25 G253A55.0B48.0I29.0J7.0T1 Where I and J values is the current position of the cutting head. Because the machine is in inch, not metric so I...
  2. Thanh Tran

    GWeike fiber laser

    @Kovo drs Do you know how to cut with fixed height hold (the laser won’t move up and down)? We want to cut something not flat so we want to keep the head not move up down to avoid crashing the head.
  3. Thanh Tran

    Edge finding function on Mitsubishi

    @laserkatana: I found programs 9503 (main), 9504 (sub x) and 9505 (sub y) in sub_program folder. Will the program detect the edge of the sheet and rotate the x-y coordinates so part will be cut inside the sheet in case the edge not align with x-y direction? I run the other laser (Gweike). It...
  4. Thanh Tran

    Edge finding function on Mitsubishi

    @laserkatana: where is the manual? Machine manual or other?
  5. Thanh Tran

    Edge finding function on Mitsubishi

    Hi, we have the Mitsubishi CO2 laser, model 3015 LPV 40CFX. Is there an edge finding function hiding somewhere in the program list?
  6. Thanh Tran

    GWeike fiber laser

    Hi, Is there anyone running the Gweike LF3015GA fiber laser? If so, is it good laser and operate easily?
  7. Thanh Tran

    Cutting galvanized material

    Hi, our company has a Mitsubishi CO2 laser, model 3015LVP-40CFX. I try to cut 0.047” galvanized material. What cutting condition can I use? Thanks
  8. Thanh Tran

    What is this error?

    &laserkatana: I used line 6 to cut the holes and line 8 to cut the rest. Then I used line 4 to cut the holes and got that error. Switched back line 6 but the error still occurred, even restarted the laser. Do you know why?
  9. Thanh Tran

    What is this error?

    Hi, yesterday I got this error. The laser Mitsubishi LV-CFX40 was running fine before my lunch. After lunch, I tried to cut a small hole 0.12” using line and encountered this error. Then I tried to use line 8 as I cut parts before lunch but the error still occurred. Restart the laser didn’t...
  10. Thanh Tran

    How to continue?

    @laserkatana: so I can do the same for just one part, dividing by boundaries. N0060(BDR:1) .. .. N0100 M87 N0110 (BDR:2) .. .. N0200 M87 N0210 (BDR:3) .. .. N0300 M87 So if I stopped after BDR:2, then I need to insert command GOTO N0210 after the command G90G92X0Y0 at the beginning of program?
  11. Thanh Tran

    How to continue?

    Hi, I am running the laser Mitsubishi LVP-CX40. If I run a program (not complete yet) then for some reasons, I stop the machine to cut something else (just an example) or power outage. How do I continue to run the program at where it was stopped?
  12. Thanh Tran

    Etching / engraving

    Increased the cutting speed then got what desired
  13. Thanh Tran

    Etching / engraving

    @laserkatana: I tried to etch on stainless steel (0.040” thickness). If I set the parameters as you suggested, the etching is too light. If I increased the power to 450W and speed 200ipm then the etching is ok as my boss wants. The problem is that the plate/part is warped due to the heat. I...
  14. Thanh Tran

    P00153 I.F ERROR

    I deleted the command lines where the errors occurred and the problem solved.
  15. Thanh Tran

    P00153 I.F ERROR

    Hi, I ran the stimulation of a program on Mitsubishi 40CFX laser and got this error. I used the MetaCam software to encode the program from dxf file. What’s the cause of error? I tried to skip one command life then the next line will be error...
See more

Part and Inventory Search

Back
Top