Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by stanjasper

  1. stanjasper

    LVD 350/13 PPE HYDRAULIC 7-AXIS CNC PRESS BRAKE

    I wanted to know if any body knows how to work the MNC 95/c controller on this press, LVD 350/13 PPE HYDRAULIC 7-AXIS CNC PRESS BRAKE.
  2. stanjasper

    FO-3015 Pierce Problem

    Thanks LASERNINJA I will see what happens with your advice. Laser operation is a little different than IT however I always welcome a challenge and thanks to the people here at Eng-tips it makes my challenge a lot easier.
  3. stanjasper

    FO-3015 Pierce Problem

    Thanks Laserninja I have tweak the setting you recommended and now my cut is cleaner with smoother edges. I actually set my gap to .1500 and move my time down to 25, intfreq to 14 and changed my tip to 2.5 double. One other thing the matrix calls for a pierce point M103A3 and M105x y , what I...
  4. stanjasper

    FO-3015 Pierce Problem

    I can't seemed to get my pierce point to cut correctly on a FO-3015 laser. I am trying to cut HRS0.75 material and when it pierces it blows the holes out and doesn't cut all the way through the material. My starting point for my pierce is: Prw. 4000 IntFreq 16 Intduty 16 IncFrq 5 incduty 1 step...
  5. stanjasper

    Cutting Conditions for Fanuc F0-3015 Laser

    Thanks Laserninja but I can't get the second link to work either.
  6. stanjasper

    Cutting Conditions for Fanuc F0-3015 Laser

    I want to follow up on this post. I have since return to cutting .500 material and it has improved 100% especially my edges. Here is my settings:Feed 35, Pwr. 4000, Freq. 700, Duty 75, Press .08, Kind 1, Nozzle gap .0600, offset .0085, Edge 0, Approach 0, Focal Point -0.031 and I am using 1.4mm...
  7. stanjasper

    Cutting Conditions for Fanuc F0-3015 Laser

    I have my settings at prw. 4000, Freq.700, Duty 75%, Gas Press. 0.06, Gas Time 2.0, Nozzle gap 0.0300, offset 0.0085, focal -0.030. Cutting HRS0.0500 A572 material. The cut is much better but still needs improvement. I don't have the 2.5 or 4.0 double nozzles they are on order. I don't have my...
  8. stanjasper

    Cutting Conditions for Fanuc F0-3015 Laser

    msandoval I do appreciate your help. I have cut .500 material in the pass and got a pretty clean cut without using the WACS head. However we just replaced 2 discharge tubes and are in the middle of a turbo replacement. I was wondering if there is a change in the machine's run-ability when...
  9. stanjasper

    Cutting Conditions for Fanuc F0-3015 Laser

    I am now cutting .187 material but as soon as I go back to .500 I will try your last suggestion. I believe that maybe turning the freq. and duty down may help my situation. Again I really thank you for your assistance. Stan
  10. stanjasper

    Cutting Conditions for Fanuc F0-3015 Laser

    Thanks for the reply jetrep. I have used these settings 1/2" HRS E4 35"/MIN 4000W 2000HZ 100 DUTY GAS 0.08 NOZZLE GAP .030" FOCAL POINT -.075" 7.5" LENS, 1.4MM DOUBLE NOZZLE. Our focal point is negative because our NC is an older model,(Fanuc 160i-l series). I am able to cut better however...
  11. stanjasper

    Cutting Conditions for Fanuc F0-3015 Laser

    I have been running a Fanuc F0-3015 Laser with a 4000 laser and I can't seem to get HRS0.500 material to cut smooth edges like my HRS0.375 material. I was wondering if any one had some baseline cutting conditions for this material. I have been using a NON WAC and a 7" focal length. Any...
See more

Part and Inventory Search

Back
Top