Recent content by sitti

Dear All, I have problems with programming Miyano BNC 34C5 lathe machine (Fanuc controller) with an LNS Quick Load Servo III barfeeder. Could somebody send me an example, what is the exact way to control the loading of the new bar? If the bar is in the lathe machine, then it is no problem, I...

Hello Everybody, I have a part, which I want to machine on a Star SV-12 machine. The machining of pink surfaces are ok (these are machined first), I'm having problem with the blue ones. The plan is to machine it with a tapered milling tool, with the needed R1 lower radius, in a driven tool...

Hello Everybody, I am planning to buy a notebook, but I want an Nx 7.5 compatible one. And if it is working fast is an advantage. I am hesitating between these: 1; Dell Vostro 3550A-2640M-4GH75DW9S Silver Intel Core i7-2640M, 4GB, DDR3, 750GB, AMD Radeon HD 6630M, WEBCAM, Bluetooth, Card...

Hello Everybody, I need a model of a clamping equipment. Is there a way to download it from somewhere? It is an OML Serie MC 150x200. Thank you for any information.

Hello Everybody, I have the following error message when try to run NX7.5 Cast. "Error, Check the value of the UGII_CAST_HTML_URL variable (). C:\Program Files\UGS\NX 7.5\UGII>" Any idea what to do? Thanks in advance.

Hello, Is it possible to change the post output unit in a default pp? If I open lathe_tool_tip.pui, I can't see where to do it. Thanks

Hello Kukelyk, Megadod a privát elérhet?séged? Üdv, Sitti sitti@freemail.hu

Hello Everybody, I want to try post builder, but I don't know how. I know that it is possible to download several post processors online, but I don't have webkey account. First I planned to make a simple 3 axis milling pp, with possibility of cutter compensation for Fanuc controller. And a...

Thank you very much for your help, all of you. Now I can use my beautiful Hungarian letters. :)

Hello Guys, Thank you for your help. But one more basic (I hope the last) question. Where and how can I change the font type? I found File\ Utilities\ Customer defaults\Drafting\General\Lettering fonts. If it's the right place, I don't know what to do with it.

Hello John, I am back, and I still have questions. If you can help me. First, I can't find the attached program. But no problem I downloaded one, but something is not ok. I have FontFactory 3.0. When I try to open latin_extended.fnx it gives the following error message: """"Sorry. Conversion...

I wanted to check my post process files, but I can find only tcl and def files. This way I think I can't open it in post builder. Then I tried to create a new one, just to try, how it works. I selected Fanuc from the library, did some modifications, and saved it. I copied the files def, tcl, and...

I checked the manual, and tested the machine with G41. If I write a simple program manually, with cutter compensation, everything works fine. The program is the following: G40 G17 G94 G80 G90 G21 M6 T20 (DIA. 10 END MILL) G43 G00 G54 X20 Y20 Z10 S800 H20 M03 G41 D20 G01 X0 Y0 F100 Y-20 X-20 Y0...

Hello Everybody, I want to use cutter compensation on a machining center with Fanuc, but I don't know what is wrong. I have a post processor, wich generates the G41, and G42 commands, but the machine is not doing it. It works like if it were programmed with G40. If I put in any radius wear, it...

I have read about many books for NX. For example "Basic to Advanced NX7.5 Modeling, Drafting and Assemblies". Does any of these available for download?