Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by shaun8567

  1. shaun8567

    Spiral bevel gear analysis

    "The gear is rigid,and the pinion is free to move on Theta." What is applying the torque load? Can you put your model?
  2. shaun8567

    Force settings Make No difference

    SolidWorks does a linear scaling of the deformed shape so that the user will be able to visually see it. If you want to compare the displacements between different materials and loads, you need to look at a displacement fringe plot and see what the maximum displacement value is on the legend...
  3. shaun8567

    ProE Mechanica, Buckling Perpendicular to the Load?!

    Can you upload the model itself? Have you looked the the 2nd, 3rd, and 4th mode of buckling? Are you meshing the geometry with solid elements? If so, be aware that the rotational DOFs on your constraint are NOT locked; solid elements only have three DOF per node (all translation). "I had...
  4. shaun8567

    what kind simulation or tool shouhld i use for this problem

    Other than hand calculations, you could use SolidWorks Motion.
  5. shaun8567

    Simulation of cutters

    I can't DL your model at work, but I do have a few pointers/questions. How did you model the pin connection? Did you use CAD geometry? If you did, then I suggest you remove the pin CAD and add in a pin connection within SolidWorks simulation (make sure to allow on axis rotation). Does a fixed...
  6. shaun8567

    Simulating A Tapered Pin Constraint

    To what level of accuracy do you need to model a tapped pin connect? Do you just need a connection that allows on axis rotation? Does it need to provide mechanical stiffness in only one direction? What level of accuracy do you need from a results standpoint? Are you wanting accurate stresses at...
  7. shaun8567

    Assembly Problems Non-Linear Analysis

    To start, Simulate/Mechanica has limited function for nonlinear analyses compared to linear analyses. For example, Simulate/Mechanica does not support shell, beam, and advanced spring elements in nonlinear analyses. A "Perimeter Weld" involves the creation of shell elements, so if you try to run...
  8. shaun8567

    stresses in a steel band clamp

    Are you asking how you'd calculate this in ANSYS, or calculate it by hand?
  9. shaun8567

    Explicit Analysis in ANSYS

    LS-Dyna is a 3D party code; do you have the license for it?
  10. shaun8567

    I want to simulate 3d-printing model with varying printing direction. any suggestion?

    I'm a little confused as to what you're wanting to do. Do you want to know the best way to model an object created on a 3d printer? Anyways, from my limited understanding of the material nature of 3d printers, I would assume a composite layer layup approach would be the best way.
  11. shaun8567

    Transient Shock Analysis in Creo Simulate vs Ansys

    Something just occurred to me that I should have caught at the start. You said you were doing a shock analysis, so I assumed you were using the Dynamic Shock in Creo. However, you said you were adjusting the damping ratio value in Creo, which is something you can't do in a Dynamic Shock (since a...
  12. shaun8567

    "one or more contact regions may not be in initial contact"

    What do your deformation results look like?
  13. shaun8567

    Uncertainty in transient simulations

    Kevin, can you provide more information was to why you can't refine your mesh further? Can you also provide some more information about what type of simulation you're doing? Are you trying to do a drop/impact test? Is the event highly non-linear, requiring non-linear dynamics? Maybe I'm not...
  14. shaun8567

    Shock Response Function in Ansys

    Hopefully I'll be able to clear up some misconceptions. The dynamic shock method come from the days when hand calculations were used to estimate the response of a structure to a transient event (like a blast, impact, seismic event, etc). This type of analysis uses a Response Spectrum Curve...
  15. shaun8567

    Patran: Replacing parts of FEM with resulting forces & moments

    If I understand what you want to do correctly, then this sounds like an ideal candidate for sub-modeling. With sub-modeling, you map the nodal displacement field results as enforced nodal displacements along the cut-faces.

Part and Inventory Search