Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Rpsfinest

  1. Rpsfinest

    steam flow calculation through a fixed orifice

    I am trying to calculate the steam flow through a fixed orifice of 2.125" diameter in a 3" pipe with an inlet pressure of 100 psig... Can anyone help?
  2. Rpsfinest

    HRSG Stack Temperature

    We currently operate 4 ABB HRSGs in combined cycle orientation. On one of the four HRSGs the stack temperature is around 60 degrees higher than the average of the other three. What would be some of the causes for this? What should I look into in getting the heat transfer across the boiler...
  3. Rpsfinest

    Harmonic Noise Index on Generators

    I am looking for a device sensitive enough to measure the Harmonic noise index on a GE 7FA generator. We usually hire GE to come onsite to perform a test to determine if the core of the geneerator is loose which may require belly bands to prevent key bar rattle. Does anyone have any experience...
  4. Rpsfinest

    Calculating efficiency loss from a tube leak

    We had a tube leak in the LP Evaporator section of the HRSG. I know the pressure and temperature in that section. I also know the size of the tube leak. (lbs/hr) How can I calculate a btu loss from the leak that I can use to show an adjustment to our heat rate? Basically I just put Fuel...
  5. Rpsfinest

    Boiler - Turbine Cycle effeciency

    I am trying to calculate the efficiency losses directly attributed to High Backpressure on the steam turbine due to an air in leak on the rupture disk. Can anyone help me out with a calc to perform, I want to see what the heat rate loss is and try to put a dollar figure on it. Also I want to...
  6. Rpsfinest

    Glycol Leak Causing pH Depression

    yes correct the condensate system is demineralized water treated with ammonia to raise ph...
  7. Rpsfinest

    Glycol Leak Causing pH Depression

    We had a small glycol leak into the condensate system at the plant. The condensate is controlled around 9.0 pH and is demineralized water. My question is on the chemical reaction between the glycol and the 9.0 pH demineralized water. It caused the conductivity to increase well out of our...
  8. Rpsfinest

    Water flow in a pipe

    piping is titanium, the low pH is necessary to avoid scaling in condenser due to high calcium levels in grey water. thanks guys
  9. Rpsfinest

    Water flow in a pipe

    was just looking for something quick and dirty...
  10. Rpsfinest

    Water flow in a pipe

    how do I use this equation? the only variables I know are that the city water pressure is around 90 psi and the pipe ID is 1"... is this enough info to calculate flow over a 24 hour period?
  11. Rpsfinest

    Water flow in a pipe

    Here at the plant on our Circulator Pumps we have booster pumps that use circ water for cooling and lubrication. Unfortunetly the booster pumps fail often due to the low pH of our Circ Water. New pumps have been order to correct issues we have had with old pumps. My question is I am trying to...
  12. Rpsfinest

    Converting MB/Hour to SCFM

    Can someone do a check on my calculation: I am trying to convert 1000 MBs/Hour to SCFM I am using 1.034 MBs/MCF So 1000 (MBs/Hour) / 1.034 (MBs/MCF) = 967 (MCF/Hour) 967 (MCF/Hour) * 1000 (SCF/MCF) = 967000 (SCFM/Hour) 967000(SCFM/Hour) / 60 (Minutes/Hour) = 16116 SCFM Does this...
  13. Rpsfinest

    Using Turbulators to increase heat transfer capabilities

    How much of an increase can you expect (ballpark) from inserting turbulators into an existing shell and tube heat exchanger? Existing heater is 10.92 MMBtu/hr. Tube side is feedwater shell side is natural gas.
  14. Rpsfinest

    Increase heat transfer capabilities from Heat Exchanger

    Curently fuel gas entering our gas preheater is at 170 deg F. The gas is raised to that temperature from a gas compressor. The gas leaving the preheater (shell and tube heat exchanger) is at around 370 deg F. We are trying to find a way to get away from the compressors because of the...
  15. Rpsfinest

    Explain Entropy?

    Can someone quantify entropy for me? I am having a hard time putting the theory of entropy to something real. Can anyone explain this concept to me using a real life example, possibly a heat transfer situation?

Part and Inventory Search