Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by resilientsoma

  1. resilientsoma

    Running valves in series/parallel for isolation/drainage

    EnergyMix, I appreciate the apology, and sorry for the counter-strike; I was too aggressive due to taking it the wrong way. Also, I was not trying to be dismissive to the other members at all. I feel bad if it came off that way. As far as an update with this, I'm pretty sure our OSHA...
  2. resilientsoma

    Running valves in series/parallel for isolation/drainage

    @ EnergyMix : Well, reading your post from the other side comes off in a different way. It seemed like you were being very sarcastic and not trying to help at all. I guess we got off on the wrong foot, a lot can be interpreted incorrectly via internet. To be honest though, I'm not really...
  3. resilientsoma

    Reading Pump Curve

    @ BigInch : Yes sir, I'm trying. Thanks for your time and patience! For an update: I'm working on nozzle selection, looking at PSI needed for area coverage. Next will be bypass constructions w/ PLC control. Fun stuff.
  4. resilientsoma

    Running valves in series/parallel for isolation/drainage

    @EnergyMix It's obvious having an expert come look at my setup, thank you for bringing that to my attention. I do not expect free consultation. If this is the case, 80% of these threads on this forum should be red-flagged. I am a new engineer and don't have all the answers unfortunately. I...
  5. resilientsoma

    Reading Pump Curve

    Sorry for the delays! I understand the trade-offs, and VFD's aren't the most ideal scenario. I will take all of this into consideration for sure. We use the pumps for constant flow for process requirements, so it's either a smaller pump, or run w/ VFD and/or bypasses. A smaller pump to...
  6. resilientsoma

    Running valves in series/parallel for isolation/drainage

    to the top ... please help! :)
  7. resilientsoma

    Running valves in series/parallel for isolation/drainage

    nobody?
  8. resilientsoma

    Running valves in series/parallel for isolation/drainage

    To the top, help please. Need to see what ways to isolate/drain 1 hydraulic line in 2 locations (see picture above).
  9. resilientsoma

    Reading Pump Curve

    @ Big Inch : Wow, what a wealth of knowledge; I truly appreciate your time. I'm feeling stupid again: I can't seem to match my pump with your 4 highlighted points. The most kW I've seen was 71.8, 115.5 A, and 59.2 Hz. The kW in the PDF are much higher. I am starting to wake up to reality...
  10. resilientsoma

    Reading Pump Curve

    @ BigInch & Artisi : From more researching and getting your inputs, I'm getting to where I need to be even more. The efficiency w/ VFD control does seem problematic. Our pumps are rated for VFD's so that is what I will look into more. I can understand your explanations and will keep this in...
  11. resilientsoma

    Reading Pump Curve

    @ BigInch : There already is a VFD for our pump, but we currently do not use it, only a set-point can be used, but is maintained at close to 95% of its 60 HZ. We have PLC control, just need to make it automatic w/ PID integration. I know there are certain concerns w/ running a VFD from your...
  12. resilientsoma

    Running valves in series/parallel for isolation/drainage

    Posting to put this thread on the top! How do I add extra valves to have in 2 locations to isolate in series and drain in parallel ? Anybody have experience w/ valves that have Interlocking?
  13. resilientsoma

    Temperature/Humidity Reduction in Semi-Closed Centrifugal Fan Set-up

    Alright guys, I'm going to assume that this is only radiant heat effects in the surrounding areas. If the cooling chamber is to become enclosed, doesn't seem like it will make the surrounding area much more hotter/more humid. I will assume it to be negligible, only a couple degrees of ambient...
  14. resilientsoma

    Reading Pump Curve

    @ Artisi : that was thought about for sure. I'm just trying to work with what we have; of course not trying to go through many rebuilds as we do now though. We do have VFD for the pumps, but are VFD's a good solution for pump protection... for low GPM, turn setpoint % down from the 60Hz ...
  15. resilientsoma

    Running valves in series/parallel for isolation/drainage

    Anyone know how to isolate/drain in series/parallel with the setup I have pictured? Am I missing something from the internet link posted by hsbcn? Thank you!
See more

Part and Inventory Search

Back
Top