Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Rana Shafay

  1. Rana Shafay

    Bystronic Bystar 3015 4.4kw

    Hi Sir Krugtech Thanks a lot after long time, we start laser again then we found that The turbine should only be run between ~60 and ~140 Kpa. Delta C2000 drive take 23 Ampere in clockwise (Forward) direction and in anticlockwise (Reverse) is 32 Amp current at 370 HZ here we are confuse that...
  2. Rana Shafay

    Bystronic Bystar 3015 4.4kw

    Hi Krugtech Sir Hope fully you will be fine, Sir we try Delta C2000 Drive its work fine near to 200HZ Acce time 70 t0 120 Sec and current is 36A,But When running the drive at 370 Hz, the dry draws too much current and triped due to overlaod. And we notice abnormal sounds in the Turbine chamber...
  3. Rana Shafay

    Bystronic Bystar 3015 4.4kw

    Hi Sir Krugtech Bundle of thanks for your valuable response. Ok We try to find Delta c2000 VFD. Please provide us a copy of parameter setup. Sir we have face some issue regarding VFD Parameter Setup. when we clear all confusion of configuration of VFD then we can replaced another VFD or...
  4. Rana Shafay

    Bystronic Bystar 3015 4.4kw

    HI Sir krugtech and Darren Bendall Any suggestion Rana Shafay
  5. Rana Shafay

    Bystronic Bystar 3015 4.4kw

    Hi Sir Krugtech We are using Bystronics laser Model 2005 , Due to water leakage Resonator NORDAC 700E 22 KW VFD Board Damaged. Now Turbine is not running , The laser machine is stop due to VFD faulty, We try to fix the problem but no success. so we are try to replaced with new another VFD. so...
  6. Rana Shafay

    Bystronic Bystar 3015 4.4kw

    Hi Darren Bell I Have faced a problem regarding Resonator Turbine motor VFD. Brother can you send me a copy of VFD parameters or tell me how much freequency at maximum rpm of turbine motor 2nd can you show me picture of VFD Wires Connector Thanks in advance...
  7. Rana Shafay

    Turbine VFD issue (Bylaser 3015 4.4kw Bystronics) 2005

    Hi Sir Need help regarding CO2 Bystronics Bylaser 4.4 kW machine model: 2005, machine power source (Rasonator) The turbine VFD BECKER type: SK 700E-222-340-A-GBB-BY damaged, so we don't have another VFD and therefore would like to replace it with another compatible one VF drivers. But we have...
  8. Rana Shafay

    how to installed MMC software in laser Co2 mosel 2005 Bystronic

    Hi Every One Due to various effect my computerof my machine, lost MMC and laser veiw software, luckly i have backup in Machine Computer. But i donot not which is the file is exact to installed again to recover MMc laser and Viewer software with parameter
  9. Rana Shafay

    HI Sir I have face a little probl

    Hi Rex Thanks a lot i have a rofine laser machine and we are used this Cylinder can we used tis ratio with LM3020D resonator , i attached piture With regard Muhammad...
  10. Rana Shafay

    HI Sir I have face a little probl

    Hi Sir IRstuff's (Aerospace) Thanks a lot of your Guide lines. sir I tell in my post that my machine is a Mitsubishi LC10V with ML3020D Resonator, I read all sending your web address and i understand that that for Co2 laser machines we used Pure Co2 or mixture of gases consist of helium...
  11. Rana Shafay

    HI Sir I have face a little probl

    HI can any body solve my issue
  12. Rana Shafay

    HI Sir I have face a little probl

    Hi Sir Thanks a lot of your good response It is 2ndphase to cut any material with laser machine , 1st phase is installation of machine, we have experience to cut any material, I mention here that during installation we have face this problem. This machine and control is new for us, we bought...
  13. Rana Shafay

    HI Sir I have face a little probl

    HI Sir I have face a little problem regarding MITSUBISHI, ML-3020D, LASER CUTTERS WITH LC10V CONTROLLER sir we don't known which type of gas (Laser Gas) used with ML-3020D, which type of combination of gases. CAN YOU GUIDE US THANKS IN ADVANCE MUHAMMAD SHAFAY...
See more

Part and Inventory Search

Back
Top