Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by R4725

  1. R4725

    Amada FO3015 Gemini

    I have power to all the legs I have marked in red in this photo. 120 volts https://files.engineering.com/getfile.aspx?folder=6cc6dff4-0a7a-43f2-824b-b472d186d3ca&file=F033AA1D-A5AE-4951-90A9-B8EC41D42F2E.jpeg
  2. R4725

    Amada FO3015 Gemini

    Trying to add a video to this rely https://files.engineering.com/getfile.aspx?folder=b3177fcb-98be-4dc1-b86b-70ac5f463a64&file=trim.95FE58C1-D1D1-45DA-96A8-7CB5ACBC43AC.MOV
  3. R4725

    Amada FO3015 Gemini

    Good day, I am having some troubles started getting a blank screen when booting up once and a while mid summer if I shut down and reboot once or twice it would boot up normal that seems to be a problem every time I shut down the NC controller now so I have been leaving it on it is also taking...
  4. R4725

    Where is Assist Gas sensor on Amada FO3015

    no it cut decent parts and stopped in the middle of a part
  5. R4725

    Where is Assist Gas sensor on Amada FO3015

    I am thinking I am having some assist gas plumbing issue. The machine was cutting parts I do other work in the shop while it is cutting check up on it every so often. I come back and the machine stopped cutting but was still moving as though it was cutting. i stopped it checked and what appeard...
  6. R4725

    Amada FO-3015 - Alarm 2154 - sensing alarm

    I messed with some used cones and different things and finally put some 5/8 plate on and WACS cone and cut perfectly, I guess the refurbished cone I received was faulty, something much change when the oxygen is flowing through there, like i mentioned it seemed to work perfectly when the shutter...
  7. R4725

    Amada FO-3015 - Alarm 2154 - sensing alarm

    With the trace off it does not follow my finger
  8. R4725

    Amada FO-3015 - Alarm 2154 - sensing alarm

    I am having the same trouble as FabproHelp, I can cut a part with shutter key off and the z trace off and it seems to work like it is supposed to following the sheet moving up and down, if I stick my finger by the nozzle it will ride up when I take my finger away it goes back down, but when I...
  9. R4725

    Assist gas regulator

    Not sure I thought I pushed refresh but I'm just now seeing your post I did check the screen at machine inlet and the screen in the regulator no improvement after cleaning the screen in the regulator. I will see how soon I can get a regulator or I will try your work around to get this job...
  10. R4725

    Assist gas regulator

    I'm having trouble with my assist gas regulator. I have had my machine for a little over a year and it has sort of been acting this way since I got it but it's getting worse (amada FO3015 4000W) all I have cut is mild steel so far but the problem I have is when it starts a cut the assist gas...
  11. R4725

    Service on Amada FO3015

    I'm looking for someplace to turn for service on my laser, footstrap, or laserninja, or any of you others do service work, or consulting?
  12. R4725

    1 inch thick with Amada FO3014 4000 watt

    Thanks alot, I will give it a try when I have a chance. I think I will hire out my 1 inch thick stuff for the bigger jobs and hopefully I can get it cutting well enough to do my prototype parts in house. Thanks again.
  13. R4725

    1 inch thick with Amada FO3014 4000 watt

    Ok I might attempt again cutting one inch again then. I am using a 4.0 double nozzle WACs off. I think this was possibly my last settings when I gave up E3 was boing used to cut the 1 inch diameter holes: 10 inch per minute 4000 watts 1000 freq 85 duty gas 0.04 E4 was 15 feed rate 100 duty all...
  14. R4725

    1 inch thick with Amada FO3014 4000 watt

    I have spent many hours trying to tune this machine to cut one inch thick mild steel with no luck. It might very well be operator though as I am quite new to operating a laser. I have had the machine cutting 3/4 inch very well though. I must have cut about 200 one inch diameter holes, well tried...
  15. R4725

    WACS on Amada FO3015

    I will try that. Thanks
See more

Part and Inventory Search

Back
Top