Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by proengineer

  1. proengineer

    IDEAS file opening

    Dear friends, I need a quick help. I got data of IDEAS in the form of .prt, .asm, .pkg files. I tried opening it in IDEAS 11 and UG NX4. But its not opening. Please advice. Amish Goel
  2. proengineer

    Frames in Intralink

    Dear Friends, I am joining back afetr a long time. I have a request to all my old friends to please think about the problem mentioned below. I am working on Intralink for a long time now on older versions. Recently after a 3.0 I have shifted to 3.3 M020. I am facing a starnge problem here. I...
  3. proengineer

    Windchill Project Plan Customization

    Dear All, We are facing a problem in Windchill Project Link that for an Activity if there is some delay in finish date then we cannot see what the Planned date was. I am trying to explain it a little more here: I have created a plan in Windchill project link in the plan we have two colomuns...
  4. proengineer

    Windchill ProjectLink

    Dear Friends, It's very strange for me to know that I hav't got a single reply on the Cost issue that I have raised. Is no one using this product? Amish
  5. proengineer

    Windchill Project Link

    Has someone has experience of doing Cost Tracking using Windchill ProjectLink? 1. There is no provision in the "Type of Resources" for putting the cost of "Hardware" & "Software" that also behave in the same manner as the resource type "Person". 2. Alternatively, if we put these resources...
  6. proengineer

    Windchill Project Link

    Dear Friends, After having an unsuccessful efforts in finding solution of my problems related to Project Link from PTC Customer support, I am looking towards you all. I am using WindchillProjectLink 7.0, Build M010. Has anyone successfully tried the COSTING part of Project Planning? If yes, I...
  7. proengineer

    Skeleton vs Part

    Thanks, I will like to put my question again in a little different manner. What are the pros and cons of making a "normal part work as skeleton" and "a true skeleton part made in Pro/E"? I have seen a company using a normal part work as skeleton. I wonder what benefit they are getting by this...
  8. proengineer

    Skeleton vs Part

    Talking in terms of Pro/E, what is the diffence in the functionalities of a skeleton over a normal part file? Both gives all the facilities of creating features, cut sections etc. Only additional benefit of using the Pro/E functionality of a Skeleton Part over a normal part file is that the...
  9. proengineer

    Catia Export

    I think you are right. I faced a lot of problem when I export it to .model. This file when imorted to Catia gives a lot of unwanted surfaces. I also tried STEP route. Though I got open surfaces here also, but these are managable. Are there any settings in Pro/E that one should set for exporting...
  10. proengineer

    Importing data from Pro/E

    Dear Kevintp, I need to have the assembly structure in Catia. By your method, you must not be getting the individual part info.
  11. proengineer

    Importing data from Pro/E

    I am new to Catia. I exported a Pro/E assembly file to ".model" using File Structure as "Ditto" i.e. the Sub-assembly and part structure of the assebly is maintained when opened in Catia. Has anyone done similar thing before? What is the quality of this data in Catia? Amish
  12. proengineer

    Texture - Rendered model Image output

    I have Pro/Photorender license. I am able to save the Texture information only in the Tiff (Snapshot) format. Amish
  13. proengineer

    Catia Export

    Well, using the license "Pro/INTF-for-CAT-II-w_ATB" gives me facility of importing and exporting "*.model" files. Thus now I have a format ".model" that I can export my Pro/E files to. Since "model" is a extension that Catia V4 recoganizes, the exported model can be opened in Catia. My second...
  14. proengineer

    Catia Export

    Which ATB Bus licence are you mentioning...Pro/INTF-for-CAT....I thought that license helps only while importing data from Catia and not vice-versa. Thanks a lot for the support. Amish
  15. proengineer

    Catia Export

    I have to export a Pro/E model to a format that can be opened in Catia. Can someone suggest the settings in Pro/E to be done and the format one should use / available in Pro/E for best data translation. Is there any special Plugin or Software that is available and can be used either while...
See more

Part and Inventory Search

Back
Top