Eng-Tips is the largest forum for Engineering Professionals on the Internet.

Members share and learn making Eng-Tips Forums the best source of engineering information on the Internet!

Register Log in
  • Congratulations dmapguru on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by pnavy

  1. pnavy

    Load Panel Purlin - Not working - Scia engineer

    Dear patswfc. appreciate your answer! Thanks,
  2. pnavy

    Load Panel Purlin - Not working - Scia engineer

    Ok. Thanks for reply. I figured this one out and your comment helped a lot. So with the learning in the software I am facing another issue, now I am wondering in which part of calculation are stiffeners used for calculation. With stiffeners I mean this setting...
  3. pnavy

    Load Panel Purlin - Not working - Scia engineer

    Hello, I am quite new in Scia Engineer and I am having troubles to impose load on purlins via load panel. I modelled a 3D frame with columns 100x100x5 and beams 100x100x5 and purlins 80x80x3 and when I make the area for load panel and the load is inserted on the load panel the load is not...
  4. pnavy

    IMPORT DRAFTING SETTINGS FROM PART

    Hello to All. Hopefuly somebody here would help me to get my drawing to look right with some settings importing. The thing is that I am quite fresh in NX and setting up all the drafting settings can be a bit time consuming especially if you have a lot of work to do. What I want to do is to...
  5. pnavy

    CAD files other than NX

    I know that I did not really hit the right tread, but I was wondering if anybody knows why when I export drawing from NX 7,5 to dwg in 2D exchange some symbols like roughness symbol, circle around annotation,etc. are not converted? But this happen only from Nx to dwg it converts ok from nx to...
  6. pnavy

    3D extend spline

    Hello, I am new on NX 7.5 and I have a bit of truble to get a nice surface to make a cut on a solid. my surface end was irregular so I trimmed it with plane and now I would like to extend the "trimmer curbe" but according to bottom extension that goes 3D. So is this possible? Many thanks...
  7. pnavy

    MACRO CATIA from cat.drawing to TIFF

    Hello, It is me again, so I use the macro and it works! But I am wondering if it is possile to edit the code so that the extension .catdrawing would not be inserted in .tiff file naming: Example: Name of CAD drawing with extension: drawing_1.CATdrawing name of converted file with extension...
  8. pnavy

    Partition problem

    Ok, If I uderstand right the problem is that the force is not applied via partitioned surface by coupling connection from RP on the whole body. why is deformation limited on coupling connection surface?
  9. pnavy

    Partition problem

    Hello, does anyone knows what am I doing wrong here! I have made a partition on solid, to limit the area where I will couple reference point. And when I apply load on RP and run the sim. I get only on partitioned parts deformation and it is not travelling thru solid (see pic.). Many thanks...
  10. pnavy

    MACRO CATIA from cat.drawing to TIFF

    ok, It works fine i did not finish the folder adress with \ like:C:\Users\....\2D\cat thanks!
  11. pnavy

    MACRO CATIA from cat.drawing to TIFF

    OK , but I am sorry to say that I still get error. source: CATIAdocuments Description: The merhod open failed Line: 18 column: 4 many thanks:)
  12. pnavy

    MACRO CATIA from cat.drawing to TIFF

    VBA, yes, it is for .pdf, but if i read correctly you can change .pdf to .tif?
  13. pnavy

    MACRO CATIA from cat.drawing to TIFF

    Hello, since I wanted to reply on all ready open thread but i could not I decided to open a new thread, for that if I am wrong I am sorry! I have started to get acquainted with some basic macro programs for catia and I found macro to convert from drawing to pdf. The problem is that I get...
  14. pnavy

    Axisymmetric stress analysis with rigid surface, stress distribution seems strange

    Hello, from me to. 2D mesh has it's downside, many times you have to analyse results with mes refinement if the peaks in the results are due to the nature of the 2D element. Just as a thought if you put force on the line that has thickness of 0 and is a part of a analysed plane the stress...
  15. pnavy

    High reduction rolling - Boundary conditions problem

    Yes, thanks I figured it out, that i was missing a key component, friction!:) And I used predefined field in inital stage as velocity that drove my profile on to the rolls. thanks!
See more

Part and Inventory Search

Back
Top