Recent content by mtchufi

Try to use ZENsoft from Omron site. http://oeiweb.omron.com/Downloads/ZS300_Trial.EXE This good for the omron beginer programmer. it has interactive simulator there. just try it.

HI. I,ve Little problem in my Old PLC. I want to change the counter value to reduce my machine step. Can any body show me the key strok to change the counter value. I use the programmer SA-20 on my old KOYO KOSTAC PLC. I hope much contribution of you. Any Repply is appreciated.

Jbartos, I've seen the contract of purching and istallation, but there is no subject descripted relevant with this case. JSright,Scotty. Its a good idea to give the coloiuring tape, and thats what have done here. If this methode (giving coloured tape) is an acceptable way, I think there is no...

Just 1% words, You can check this URL: http://www.sea.siemens.com/step/pdfs/acm_2.pdf hope you 'll find what u need. Mtchufi,bekasi

Thanks, Jbartos/Scottyuk I 've same idea with you, and I connected as what the vendors ask. I put a large size banner of Warning letter/Notasion in the sub distribution panel, so every one who will work with this panel know that the connection inside is not standard and would pay more...

I come again, Now I have a practical problem connection with case above. I just Installed my new machine, (from Japan). The Vendor ask me to connect the anconing panel control with the Green yellow as the Ground (as standard rule). But all in my Sub distribution panel (SDP), the green yellow is...

sallute! I've succesfully open and downloaded the link above. Thanks for your help. case closed,(any one have Idea, still welcome) Regards Mtchufi

I've set the new inverter with exactly same data (the type of the inveter is same, just different power rate), The display of the old inveter is still work, but cannot drive the motor, so I can copy the parameter exactly same. yes you're rigdht, that whan I try to set the electronic thermal...

Killemall, Your suggestion is nearly the answer what I need, but It would me more complex, because the common convention here is used the blue color as the neutral, It would give some more problem here. Jbartos,. I try to check at IEC website but I couldn’t find the page I needed. Could you...

Hi Freind, I've just replace a broken inverter 0.1 Kw 200 V with new inverter 0.4 Kw 200 V. The Inverter is used to drive a small transfer motor 0.1 Kw. I can't find any inverter with the same rate, and I change with the higher rate.For a moment, it looks OK. My Question is, does any effect for...

Thanks to all, That’s right. I’m not work in UK or US, I work in Indonesia. Here the law for electrical installation is very soft. Every one who have little known about installation may become and electrical contractor. Without license or something else. It’s strange, but it’s true. When I...

Dear all, I ve a little simple problem with my installation. As I’ve learn in collage and read some reference book, the green yellow cable is only used for the grounding cable. What I find here is, the green yellow cable is used for phase. The Distribution cable color is yellow, blue, black, and...

Hi, You can try to chek in www.plcman.co.uk to down load an old version Medoc software, wish it would helpful for you. just tyr it!

all of your unswer is Helpful to me. What happen here is , a lot of our installtation (i think this what usually done in our Country) does not have the earth leakage or ground falut detector (relay). Thats way in this case I still prefer to use the Neutral groundel as well, so when some ground...

Thanks to all repliers, You are right that I do not work in USA area. I work in a second country in south east asia region, that the regulation of electrical installation is very soft. Now, lets back to the case issued above, here is a sample case what happen in my factory last few month when I...