Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by msii

  1. msii

    Pipe sizing for Spray Nozzles

    Hi All, I'm designing a compressed air system that gets a connection from a Plant Air compressed system at 7 barG. I want to size the connecting piping in the way that it can provide enough flow and pressure to the all spray nozzles in attached. There are two types of nozzles (S1 and S2) need...
  2. msii

    Allowable Nozzle Load Curve for Integrally Geared Comp

    Hi all, I have a curve from a compressor supplier that provides Allowable nozzle loads based on the attached values (A line between Maximum force and maximum Moment). When I do Caesar II analysis I get Fx, Fy, Fz, Mx, My, Mz values at the nozzle location. How can I relate the F and M values...
  3. msii

    Small Tank Inspection

    Hi All, We have a 12 m3 above-ground Diesel tank and fuel bowser fabricated and installed in Australia. For the person who does the inspection and maintenance on this diesel tank, is there any certification or qualification required in Australia that he needs to have? Such as the Type B...
  4. msii

    Plastic strain to linear stress relation

    Hi All, i received a stress analysis done in abaqus and have a question as using Inventor Professional 2022 to do similar analysis. In the received report instead of the stresses it talks about residual plastic strains in the material. If i want to do a linear static analysis in Autodesk...
  5. msii

    Crane Railhead Corner Radius vs. Wheel Tread Flange Fillet Radius

    Hi Mint, Thanks for your response. Do you know European or US standard that refers to this issue? I cannot find any particular one in this regard. Thanks,
  6. msii

    Crane Railhead Corner Radius vs. Wheel Tread Flange Fillet Radius

    Hi All, I am working on a crane that will be used in Australia and I thought that people working in the railway or crane industry may be able to assist me. According to the Australian standard AS 5228.1-2021 (Table 101) and AS 1418.1-2002 (Table 7.20.3.6), the fillet radius between the tread...
  7. msii

    Vibrating Motor Required Bolt torque

    Hi All, For a similar applications and a different motor fabricator, the bolt torque that the supplier provided us was 50% of the yield stress of the bolt. So, I'm a bit concern about of probability of the casing breakage if I want to torque it up to 70% yield. thanks,
  8. msii

    Vibrating Motor Required Bolt torque

    Thanks guys for replying. I m looking to find the minimum torque that i can use to avoid breakage of the casing and in a same time can keep the drive in place. I m thinking of using bolt grade 8.8 for this motor but using the torque specified in the standard bolt table is too high and may break...
  9. msii

    Vibrating Motor Required Bolt torque

    Hi all, We have an unbalenxed vibrating exciter for a vibrating screen and require to know what bolt torque is required to fasten the vibrating motor to the screen frame? Considering the point that the motor is an old one and the manufacturer is not available is there any way calculate the...
  10. msii

    Quicklime Slaking

    Hi hacksaw, I need to find out amount of Dust and Steam coming out of slaking process not amount of water required for slake to be done. thanks,
  11. msii

    Quicklime Slaking

    TiCl4, I checked with the guys and they are saying that Emission requirements forced them to use a dust extraction system (Wet Scrubber). Again no difference in my scope as I need to know the amount of steam and dust coming out of the slaking system. how should I calculate it? thanks,
  12. msii

    Quicklime Slaking

    Hi Guys, I'm based in New Zealand now. It is located outdoors. Almost in all clients' sites, there are some Wet Scrubbers for quicklime slakers that collect the dust and sucks the steam out of the slaker mill. there are not many articles published in lime subject. I'll try to contact these guys...
  13. msii

    Quicklime Slaking

    Hi All, I need to design a dust collecting/extraction system (Including ducting and fan selection) for a slaking ball mill that slakes Quicklime material and want to know how much dust and steam comes out of the slaking ball mill that I can design correct ducting and select a proper fan. The...
  14. msii

    Water Vortex Calculations

    it is the sketch. any thoughts? https://files.engineering.com/getfile.aspx?folder=f85bcbea-0a04-41f8-8dc0-c7b0204f5563&file=1.jpg
  15. msii

    Vortex mixer

    Hi Guys, As it looks like it is a simple cone as attached. Any idea what the film thickness calculation would be? thanks,
See more

Part and Inventory Search

Back
Top