Recent content by mihir5577

Hi, I want some clarification as per PG-11 - Standard Pressure Parts, That if anybody built welded Water Coulm as per PG-11, and if there was no any markings (Heat #, Matl spec. etc..) on all welded standard parts (Like Caps, Ring- Joint, extenders etc.), than is this acceptable or not? As per...

Hi, I want some clarification as per PG-11 - Standard Pressure Parts, That if anybody built welded Water Coulm as per PG-11, and if there was no any markings (Heat #, Matl spec. etc..) on all welded standard parts (Like Caps, Ring- Joint, extenders etc.), than is this acceptable or not? As per...

Hi, Thanks for quick reply. But i also want some clarification as per PG-11 - Standard Pressure Parts, That if anybody built welded Water Coulm as per PG-11, and if there was no any markings (Heat #, Matl spec. etc..) on all welded standard parts (Like Caps, Ring- Joint, extenders etc.), than...

Hi, I need guidence that, Are there any ASME code applies to welded water column, which will going to mount on ASME I (high pressure steam) boiler? What marking/stamping require on welded water column as per ASME I????? Also waht markings require on gauge glass body as per ASME I? I need...

Hi, i need guidence to calculate "lOADING CALCULATIONS" for vertical pressure vessel, which stands on ANSI "L" Angles. Which calculations require as per UG-22? Are there any free software / online calculations available? Pls. guide me ASAP. Thanks Mihir5577

Hi, I want to know, that how to calculate allowable steam nozzle loads for ASME-I boiler? I also want "WRC 107 CHARTS"! FROM WHERE I GET THIS? Is this possible to download? Pls. guide me ASAP. Thanks Mihir55577

Hi, Thanks for quick reply. Now i want to know, that if the distortion is more than 1% of the mean diameter?, than is it acceptable or can we fix it? pls. guide me. Thanks in advance Mihir5577

Hi, Pls. i want to know, that, if the 12" & 8" std. wall, SA-53 B PIPE was fell down and od changed to oblong, than is this allowed as per ASME IV? what is allow for UNEVEN OD of pipes as per ASME IV???? Pls. reply me ASAP. Thanks MIhir5577

Hi, Any one can guide me that, can we use ASTM A-53 B material instead of ASME SA-53 B material in hot water boiler ASME-IV? where all our registered dwgs. are according to SA-53 B! If yes, do we have to do any documentation? Pls. guide me ASAP. Thanks Mihir5577

hi, Is ASME sec I allow patching at bigger hole to make it smaller as per diameter of down comer od?I.e We made offset hole on drum and now we have to move down comer appx. 1", so can we patch that 1" offset howl with the same matl. and thkness of pipe? Also can we do PWHT again on the area...

Hi, I just want to know that, Is ASME sec I, allows leak during hydrotest of boiler with power piping from mechaincal joint (Threaded connection)? If yes, Which para of ASME I and not Then also which para of ASME I. Thanks Mihir5577

Hi, I want to determine STRESSES in the nozzles due to applied loads. Because our customer want to calculate steam piping. i want to calculate loads in X, Y, & Z direction. Thanks Mihir5577

Hi, From where i can find details about WRC-107 and WRC-297? What i will have to do? Pls. awaiting your prompt reply. Mihir5577

Hi, I want to calculate this for steam piping analysis. so how to do it? could u pls. explain me in detail. Somebody told me that there is online calculation available, but i forgwt the website! pls. guide me ASAp. Thanks Mihir5577

Hi, Is any one tell me that how to calculate steam outlet nozzle load calculation in X,Y, & Z direction? Pls. help me ASAP. Thanks in advance. Mihir5577