Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by luky

  1. luky

    AGMA2015/915-1-A02

    help me!!! hi all of you, someone have this paper? thanks a lot!!! Diane
  2. luky

    broaching

    does anyone help me to find the right formula? i looking for how amount the broaching force to cut 8.46dp, length of cut 3.4dp and 74 teeth work material is carbon steel the broaching pitch is about 0.5dp so the number of engaged teeth is more or less 7 thank you very much Diana
  3. luky

    calculate broach load

    hi! does anyone help me to find the right formula? i need the broaching force necessarely to cut 8.46dp, length of cut 3.4p and 74 teeth work material is a carbon steel the broaching pitch is about 0.5 so the number of engaged teeth is about 7 thank you very much Diana
  4. luky

    calculate broach load

    does anyone help me to find the right formula? i need the broaching force to cut 8.46dp, length of cut 3.4dp and 74 teeth work material is carbon steel the broaching pitch is about 0.5dp so the number of engaged teeth is more or less 7 thank you very much Diana
  5. luky

    factory unknown

    someone have ever heard factory named as ORAMT (hobbing machine), DEMAK (hobbing machine), HERZUS (broaching machine), HAMBURG (shaping machine)? any suggestion is well come thank you for the replay Ester
  6. luky

    VDI / VDE 2608 norma

    thank you very much Mr. CoryPad Eszter
  7. luky

    VDI / VDE 2608 norma

    hi! someone has got this paper? thank you very much Eszter
  8. luky

    broaching force

    hi i need / look for an excel prog that help me in calculate broaching force noto module / DP, OD, material to broaching, shift coefficent thank you in advance luke
  9. luky

    semitopping

    hi! i've got a question that drive me crazy .. about involute fillet intersection diameter at the tip of teeth. how do i calculate the diameter in wich semitopping start? thak you very much giorgia c.
  10. luky

    Gear Generation software

    thank you very much mr Gearman. i have acadLT and it doesn't work lisp prog. i'll try to download the "extender" then i'll tell you the results. best regards luke
  11. luky

    Gear Generation software

    mr. gearman i have the same problem. got a hob with semitopping but don't know what the tip chamfer is if i change the number of teeth from 18 to 33. could you help me? i've read that you with the help of mr. diamondjim got a result. best regards luca
  12. luky

    grinding technology

    hi all, someone can tell me in poor words which are the most used method to grnding spur gear? and .. what is the difference between (for example) Niles and Kapp or Opal machines? are there any web sites where i can found the information that i'm looking for? thank you very much for help Luky
  13. luky

    SAE?

    hi!! i've got an external spline with 36 teeth, internal diam 38.75mm (1.52 inches)and external diam 41.65mm (1.64 inches) pressure angle 45 degree and Sndp 1.675mm. someone can help me to define which is the correct standard? if it would be a SAE standard could you send to me some information...
  14. luky

    UNI ISO 4256

    Mr. Gearguru i say thank you very much for the help. thank you very much indeed
  15. luky

    UNI ISO 4256

    ok Mr. Gearguru i wait for your monday post .. thank you
See more

Part and Inventory Search

Back
Top