Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by kyhln

  1. kyhln

    Is it make sense if I try to optimize screw conveyor?

    So if I cover the screw with a material, which can reduce the friction, I will see energy saving. This is the best way right?
  2. kyhln

    Is it make sense if I try to optimize screw conveyor?

    then it doesn't make much sense to carry out this idea, am i correct? There is alot of corrosion in our screw conveyors, they carry calcite stone. So, i thought may be i can use a different screw with different material. But if it will not affect the energy consumption, it doesnot make any...
  3. kyhln

    Is it make sense if I try to optimize screw conveyor?

    Hi everyone. I work in a factory. They have around 200 screw conveyor. The material of this conveyor is steel. As you may understand steel is heavy and there is high energy consumption. My plan is to change the material of screw conveyor. Instead of steel I may use a much more lighter, not heavy...
  4. kyhln

    How inital design can be chosen for a composite?

    I would like to investigate topology optimization of laminate composite with different initial designs. Are there any work, researchh papers or examples for inital design of laminate composite. For instance curved, flat ettc...???
  5. kyhln

    HOw can i define the forces and constraints on composite plate?

    I have a compsite plate 400x400 mm and easch ply has 0.5 mm thickness. I would like to carred out linear static analysis. In each paper, every body apply different constraints and forces. I applied the force on the middle of the plate (1000 N) and constraints are two parallel edge of the plate...
  6. kyhln

    How can I carry out the free-size/sizing and suffle optimization in abaqus?

    I should carry out optimization in abaqus. In optistruct there are three steps to design a composite optimization. 1. Free-size optimization, 2. Sizing optimization and 3. is Suffle optimization. Although In optistruct there is free-size optimization part, there is no such an option in Abaqus...
  7. kyhln

    Are there any useful sources for topology optimization of laminar composite in abaqus?

    I should carry out a topology optimization of a laminar composite material with changing of angle and thickness. arae there any useful cource for that?
  8. kyhln

    How dependent on the initial structure is the optimized solution?

    I will research a initial topology of laminar composite. How dependent on the initial structure is the optimized solution? how the simulation could look like. What different initial states are interesting?
  9. kyhln

    Which software can be used for topology optimization (lamiinar composite)?

    I will start to topology optimization of laminar composite. Which software can be used and what are the pros and cons?
  10. kyhln

    Why number of elements should be shown in an article?

    I got it now! Thank you so much
  11. kyhln

    Why number of elements should be shown in an article?

    Can yo please open this ? I am new in this topic
  12. kyhln

    Why number of elements should be shown in an article?

    I wonder that why number of elements are shown in a paper like 252455 elements are used..? Why it is important?
  13. kyhln

    How Can I Activate CFD in Abaqus?

    Hi everyone! I downloaded abaqus crack with tosca and ısight. I chose every option. But when I run abaqus there is only sandard explicit and electromagnetic model option. How can I use CFD option or how can I insert CFD into Abaqus? There i tosca fluids but I dont know how can use it. Could you...
  14. kyhln

    How can i open .stl file in abaqus?

    It was easier way than i tried :) it worked. Thank you. @FEA way
  15. kyhln

    How can i open .stl file in abaqus?

    Hi, I try to work on biomechanics of skull in Abaqus. I got CT images of skull, and then i converted images to 3D model in 3D slicer software, i exported it as .stl file and i load it to blender software to smooth and fix skull's parts. I exported it as .dxf file but abaqus use .dxf file as 2D...
See more

Part and Inventory Search

Back
Top